A helical compression spring is to be made of a steel wire. If the coil diameter is limited to 12 mm and a spring index of 6.4 is chosen. From the following wire size chart, determinethe correct gauge size of an off-the-shelf spring wire to be used. [gauge]BAS GAUGEINCHMILLIMETER1624.123.25 mmpoups2.39mm10 gange0812.06mm0641.63mm16CST"1.29 mmDAY1.02813635 mm24 P508 mm20 gangeOMOXY330254X14

Answered: Image /qna-images/answer/2174599d-910e-411c-91f5-e7254ab62157.jpg

Answered: A helical compression spring is to be…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

24
Please use ANSYS SOFTWARE
Please show work for practice problem 12
Hi can you please help me with the attached question?
i. If you know that any strain gauge has a sensitivity towards temperature.In other words, any change in the temperature could also affect theresistance value. How can we get a correct reading from strain gaugesand get rid of the temperature effect?ii. In an AC LVDT system, measuring the output voltage alone gives anindication of the displacement from the center, but not the direction ofdisplacement. Explain why, and also explain a method for solving thisproblem.iii. In a vortex flow meter, there are many methods that could be used tomeasure the effect of vortices and measure the flow rate. Explain howvortices could occur in this flow meter, and explain three methods thatcould be used for measuring the effects of vortices in a vortex flowmeter.iv. Explain in details how can we use a capacitor to indicate the lever ofwater in a tank (use drawings and electrical diagram to elaborate on yourexplanation).Page 5 of 63v. Bimetallic strip could be used as a temperature detector. Explain…
The gauge factor of a strain gauge is defined as: Select one: O a. e*AR+Vex O b. e/(AR/R) O c. *AR*R*Vex O d. (AR/R)/E O e. None of these options
Strain gauges are a standard sensor to convert deformation into an electrical signal and are used in many applications. Describe how train gauges could be used to measure (i) acceleration; (ii) fluid pressure. Use a sketch for each case to illustrate how they are used.
SOLVE CAREFULLY!! Please Write Clearly and Box the final Answer
known. Using simple measurement tools, the following features are measured. A spring is known to be made from music wire, ASTM A228 steel, however no other data are Free length of the spring was 44.45 mm. Outside Diameter was 14.25 mm Wire diameter was 1.4 mm The ends are squared and ground The total number of coils was 10.0 This spring will be used in an application where the normal operating load is to be 62.28 N. (Take 1 inch = 25.4 mm) a) Determine the inside diameter, spring index and Wahl factor. b) Determine the expected stress at this operating load. c) Determine the spring deflection at the normal operating load. d) Determine the operating length, solid length and the spring rate. e) Determine the coil clearance and check the spring against buckling. Datermine the minimum hole diameter for the spring to operate in.
Dogs, like many animals, stand and walk on their toes. (Figure 1) shows the rear foot and leg of a 20kg dog along with the relevant distances and angles. The Achilles tendon pulls on the heel at an angle 15° from vertical. Part A What is the tension in the tendon if the dog is supporting one fourth of its weight on each foot? Express your answer with the appropriate units. F = N CalfmuscleAchillestendon15\deg 45\deg 9.0 cm 4.0 cm Calf muscle Achilles tendon -15° -45° 9.0 cm 4.0 cm
The Answer is one of the options below please solve and circle the correct option .
1.The thickness of a gage block is measured five times using an instrument that has a resolution of 0.001 cm. The following measurements are obtained (in cm): 1.100, 1.110, 1.090, 1.095, and 1.105. The true gauge block thickness is known to be 1.050 cm. Use this information to answer the following questions: a. What errors or sources of measurement error can be identified in the example? (Hint: there are three). Identify each one as a random or systematic uncertainty. b. Estimate the magnitudes of each of these uncertainties. Wherever possible, estimate random uncertainties at a 95% probability/confidence level. c. Based on the uncertainties determined in part b, estimate the overall uncertainty of a measurement obtained by this instrument.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS