(a) Find the number for minimum slip gauges required to set 44.465mm size using standard slip gauge set (BM1- 447 -11) shown in the tabular column(below) and write down the steps in setting the mentioned size. Slip gauge set for MITUTOYO BM1-447-11 Range (mm) Increment Number (mm) of pieces 1.01 -1.19 0.01 19 1.2 -1.9 0.1 8 1.0 - 9.0 1.0 9. 10.0 - 100.0 10 10 1.005 1 Total Number of Slip Gauge 47 (Please Write the answer(steps in slip gauge setting) in a paper and upload in the separate submission link provided ) (b) Sketch and explain end milling operation.

(a) Find the number for minimum slip gauges required to set 44.465mm size using standard slip gauge set (BM1- 447 -11) shown in the tabular column(below) and write down the steps in setting the mentioned size. Slip gauge set for MITUTOYO BM1-447-11 Range (mm) Increment Number (mm) of pieces 1.01 -1.19 0.01 19 1.2 -1.9 0.1 8 1.0 - 9.0 1.0 9. 10.0 - 100.0 10 10 1.005 1 Total Number of Slip Gauge 47 (Please Write the answer(steps in slip gauge setting) in a paper and upload in the separate submission link provided ) (b) Sketch and explain end milling operation.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(a) Write down the slip gauge selection for 162.83 mm using standard BM1-447-11 slip gauge set shown below. Slip gauge set for MITUTOYO BM1-447-11 Range (mm) Increment Number (mm) of pieces 1.01 -1.19 0.01 19 1.2 -1.9 0.1 8 1.0 - 9.0 1.0 9 10.0 - 100.0 10 10 1.005 1 Total Number of Slip Gauge 47 (b) A grinding wheel is written with the following specifications Q C 16 G 7 B 18. Identify the specification "C", "G', "7", "B" on the grinding wheel and define any two. Enter the student ID in the box and Upload the handwritten answers in the separate link provides
(a) Write down the slip gauge selection for 157.28 mm using the standard BM1-447-11 slip gauge set shown below. Slip gauge set for MITUTOYO BM1-447-11 Range (mm) Increment Number (mm) of pieces 1.01 -1.19 0.01 19 1.2 -1.9 0.1 8 1.0 - 9.0 1.0 9 10.0 - 100.0 10 10 1.005 1 Total Number of Slip Gauge 47 (b) A grinding wheel is written with the following specifications KA 30 J 6 S 25. Identify the specification "A", "30", "J", "S" on the grinding wheel and define any two.
The least count of the main scale of a screw gauge is 1 mm. The minimum number of divisions on its circular scale required to measure 5 um diameter of a wire is (a) 50 (b) 200 (c) 500 (d) 100 The pitch and the number of divisions, on the circular scale for a given screw gauge are 0.5 mm and 100, respectively. When the screw gauge is fully tightened without any object, the zero of its circular scale lies 3 divisions below the m an line. The readings of the ain scale and the circular scale for a thin sheet ar 5.5 mm un 18 respectively, the thickness of this sheet is (а) 5.950 mm (c) 5.755 mm (b) 5.725 mm (d) 5.740 mm
1.The thickness of a gage block is measured five times using an instrument that has a resolution of 0.001 cm. The following measurements are obtained (in cm): 1.100, 1.110, 1.090, 1.095, and 1.105. The true gauge block thickness is known to be 1.050 cm. Use this information to answer the following questions: a. What errors or sources of measurement error can be identified in the example? (Hint: there are three). Identify each one as a random or systematic uncertainty. b. Estimate the magnitudes of each of these uncertainties. Wherever possible, estimate random uncertainties at a 95% probability/confidence level. c. Based on the uncertainties determined in part b, estimate the overall uncertainty of a measurement obtained by this instrument.
SECTION B: OPTION 1 Convert figure below into ISOMETRIC & Do not dimension the drawing. All units are in mm. F.V 8 T.V R30 030 25 100 2 35 10 20 OF
Find the taper angle, in radians, for a workpiece if a sine bar method was used. The stacked height is composed of the following gauge block values, 10, 15, 30, 4.5 and 1.3 mm. the length of the sine bar is 140mm. Support your answer with sketch.
If the vernier gauge reading for a specimen is 22.24 mm and DTI observation in divisions are 7, 0, & -2 respectively, find the actual size of the specimen in mm. The actual size of the specimen (in mm)=
Calculate the total reading for the Dial test indicator shown in the figure 90 10 80 fe 20 .7 6 0.01-10mm 70 www.stefanelli.eng.br /30- Eduardo J. Stefanelli 60 40 50 Answer: 9-
Please find the Grashof classification and the Barker classification of the two four-bars: (NOTE: distances are in non-dimensional units. Can use inches or cm) P1) L1=d=4, theta1=0 degrees, L2=a=1.6, theta2=60 degrees, L3=b=5.5, L4=c=4.5 P1) L1=d=1, theta1=0 degrees, L2=a=1.25, theta2=120 degrees, L3=b=1.5, L4=c=2 Please also draw the four-bars to estimate the unknown angles theta3 and theta4.
A slip gauge setting height 53.155 mm is observed when a sine bar of the length 127 mm is used during the precise angle measurement of a workpiece in a workshop. Find the angle of the workpiece in degrees= (Enter at least 4 digits after decimal points)
Using the set of slip gauge given below, determine the minimum number of slip gauges and their sizes to stack up to 67.247 mm. Show all workings and calculations. Clearly list the size of the slip gauges selected. Range mm 1.001 - 1.009 1.01 - 1.09 1.1 1.9 - 1-9 10 - 90 Steps mm 0.001 0.01 0.1 1 10 No of Blocks 9 9 9 9 9
State (a) the precision, (b) the accuracy, and (c) the greatest possible error of the following measurement number. 509psi