A differential manometer is attached to pipe (φ=10cm) which deposites a volume of 5 drums an hour , lubricant with S= 0.90. if the diameter of the pipe is double with respect to the contriction, determine the following: if it will be transporting mango juice with S=1.02, does the system is applicable, why?

A differential manometer is attached to pipe (φ=10cm) which deposites a volume of 5 drums an hour , lubricant with S= 0.90. if the diameter of the pipe is double with respect to the contriction, determine the following: if it will be transporting mango juice with S=1.02, does the system is applicable, why?

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.13P

See similar textbooks

Related questions

Q: After fracture, the total length was 53.086 mm and the diameter was 9.982 mm. Plot the engineering…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Problem 9: Castor oil (SG = 0.96) A tank whose bottom is 18 inches x 18 inches is filled with 2 in.…

A: Give data: The unit weight of caster oil = specific gravity of caster oil x unit weight of water =…

Q: 4. Calculate the Reynolds Number for 6-inch (diameter) production tubing assuming West Texas Crude…

A: Since; Q1 = 500 STB / day = 5005.434 * 105=9.20*10-4 m3 /s

Q: (c) Venturi-type flowmeter shown in Figure 5 is used to obtain the flowrate of oil inside a conduit.…

A: ## solution of venturi type flow meter, and calculation of volume flow rate, mass flow rate,

Q: Paint issues from the tank at a flow rate of 45 ft^3/s. Find the kinetic viscosity in ft^2/s. Assume…

Q: A = Roll 16 kN/m' 6 m 4 6m + M = 96 kNm 4 m B = Pin

Q: The ceramic disk used in null pressure plate apparatus does not allow the air to flow; however, free…

A: In the lab, soil-water characteristic curves can be measured using common testing equipment like the…

Q: Q4/ SAE 30 oil at 60 °F flows through a 2-in.-diameter pipe with a mean velocity of 5 ft/s.…

Q: B-A thickener is designed to separate suspension containing 15 Kg of water/Kg of solid is to be…

Q: For the closed tank with Bourdon gauges tapped into it "see figure (2)", What is the specific…

A: This question is from fluid mechanics In this question in a given with a closed to tank and gauge…

Q: y 30 kPa el.30 m alcohol From the figure shown, the alcohol surface is subjected to of 30 kPa.…

Q: In a given setup, distilled water flows towards the inside and goes outside of the vessel as shown…

A: Velocity of inflow through pipe 1, V1=30ftsecdiameter of pipe, d1 =3in =312ft =0.25ftOutflow rate…

Q: 1. Describe the basic principles of dilatometer testing. 2. List the main component in dilatometer…

A: Introduction- The Dilatometer test is used to determine the strength and deformation qualities of…

Q: point B. (b) between the two pipes, which has a greater pressure? HO B 125 mm 350 mm Hg 175 mm -i-

Q: The bottled cider (SG = 0.96) in the figure is under pressure as shown by the manometer reading.…

A: Let us analyse the question in step 2.

Q: EXAMPLE 2 A body of 12 mm diameter is tested and the following results are noted. gauge length…

A: poisson's ratio= 0.0125young's modulus = 176838.826 N/mm2explanation is given in below step

Q: A differential "U"-tube manometer containing mercury of density 13000 kg/m³ is used to measure the…

A: Given data U tube manometer Density Height of columns To find Pressure difference

Q: A steady push on the piston in a syringe is shown in the figure causes a flow rate of 0.4 ml/sec.…

Q: Strarting from the velocity distribution in pipes given below. Vmax 1 V = 5.75log10 9.0 (€) V. *…

A: From the given relation,

Q: c) The orifice flowmeter shown in Figure 4 is used to obtain the flowrate of oil inside a conduit.…

A: Given: d=1/3D, D=6cm, x=7cm, Pressure difference=25KPa, SG of oil=0.95, Cd=0.6 To calculate the flow…

Q: Whiskey (SG = 0.6 and ν = 5.0 x 10-7 m2/s) is drawn from a large tank through a smoothed, rubber…

A: Given Head available = 5-1.5=3.5 m

Q: s immersed Lermine the height of the capillary rise of water Given at 20°C unit weight of water

Q: Question 5 The Atterberg limit data sheet of an experimental session is given below Sample no 1 3…

Q: Paint issues from the tank at a flow rate of 45 ft^3/s. Find the kinetic viscosity in ft^2/s. Assume…

A: We have to determine the kinematic viscosity

Q: C3. Provide solution using the Moody diagram Oil (RD 0.8) with viscosity 0.06 Pa.s flows in a cast…

A: Relative density, G =0.8Viscosity = 0.06 pa.sLength of the pipe, L =100 mDiameter of the pipe, d =…

Q: Paint issues from the tank at a flow rate of 45 ft^3/s. Find the kinetic viscosity in ft^2/s. Assume…

A: Given:- Flow rate = 45 ft3/sec To find:- From the given question it is required to calculate…

Q: Problem 1. A solvent used for plastics manufacturing consists of cyclohexanol in pipe A and ethyl…

A: Draw the figure.

Q: 1. [Ch4 – 2] A hydraulic oil with the absolute viscosity of 0.09 N.s/m² and specific gravity of 0.9,…

A: As per honour code we will answer the first question since exact one was not specified. Please…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The bottled cider (SG = 0.96) in the figure is under pressure as shown by the manometer reading. Compute the net force on the 2-in radius concavity in the bottom of the bottle. A AL 5in 3in +4in→ 7 in = 2 in Mercury Fig. 5-17 Unit of the Correct Answer: Ib Decimal Places required in the final answer: none
Solve it correctly please. I will rate accordingly
dear eng ans quickly
7) section A mean Part A of this question
Read the question carefully and give me right solution according to the question.
Kindly give me right solution with clear calculations. Please don't copy from chegg answers.
A differential "U"-tube manometer containing mercury of density 13000 kg/m³ is used to measure the pressure drop along a horizontal pipe. If the fluid in the pipe is water and the manometer reading is 0.65m, what is the pressure difference between the two tapping points? Fluid density Pw A B a b datum Manometric fluid density p Hg Figure of manometer setup
Please answer and show all of your work.
We have a quadrant tank as given in the first picture. Breadth (B) : 75 mm Inner Radius (R1) : 100 mm Outer Radius (R2) : 200 mm Moment Arm (R3) : 200 mm weight for case1 : 65gr weight for case2: 420gr question is given in the second picture.
The data set of the diameters of the metal cylinders manufactured an automatic machine has sample size of n=28, mean of x= 49.94 mm and std. of S = 0.15 mm. Expected diameter of metal cylinder is µ = 50.00 mm. Can we be 95% confident that machine calibrated properly? Solution: v=n-1=27 ; ta/2=? P[X for 2 S VR μ+ (a Sl Vi -1-a =0.95
Strarting from the velocity distribution in pipes given below R Vmax V V₂ 5.7510910 obtain the relationship for the ratio of maximum velocity to average velocity in terms of Darcy-Weisbach frictioin facror and show that this ratio increases with the friction factor,
B- A thickener is designed to separate suspension containing 15 Kg of water/Kg of solid is to be thickened to a sludge containing 4.5 Kg of water/Kg of solid in a continuous operation. Calculate the minimum area of a thickener required to effect the separation of mass rate of feed of 103 Kg/s of solid? p H₂0 = 1000 kg/m³ ps = 6000 kg/m³ De=0.002 m R' pu 10% 10³ 10² 10 100% 101 10 2 10:3 Region a 10 2 10 1 TELEGRAM MOTION OF PARTICLES IN A FLUID 10° Region b 10 R puz Region c = 0.22 10² Re' R/pu² versus Re' for spherical particles 10³ 10⁰ 105 Region d 10 10