1. [Ch4 – 2] A hydraulic oil with the absolute viscosity of 0.09 N.s/m² and specific gravity of 0.9, is flowing in a 30-mm- diameter pipe at a velocity of 6 m/s, determine: a. The Reynolds number? Is the flow laminar or turbulent? b. The head loss due to friction in units of bars for a 100-m length of smooth pipe.

1. [Ch4 – 2] A hydraulic oil with the absolute viscosity of 0.09 N.s/m² and specific gravity of 0.9, is flowing in a 30-mm- diameter pipe at a velocity of 6 m/s, determine: a. The Reynolds number? Is the flow laminar or turbulent? b. The head loss due to friction in units of bars for a 100-m length of smooth pipe.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pipe bend shown in the figure is in a horizontal plane. Oil with a specific gravity of 0.86enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa.Determine the force required to hold the bend in place. Neglect any energy loss in the bend.
For the closed tank with Bourdon gauges tapped into it "see figure (2)", What is the specific gravity of the oil , and The pressure reading on gauge (C)?. PA=50kPa 0.5 m Air 1m Oil Pa 58.53kl 0.5 m 1m Water Pc=? kPa 0.5 m kak→→→→K→→→K Figure (2)
For the laminar flow of an oil having dynamic viscosity, μ = 2Pa in a 0.5 m diameter pipe, the velocity distribution is parabolic with a maximum point velocity of 5 m/s at the centre of the pipe. The pressure gradient for the given flow condition will be
Q14) The below configuration is consisting of two different fluids with different heights. These fluids are not mixing with each other as shown. Calculate the height, h of the manometer where the fluids will stay in balance. For the fluids, pi = 800 kg/m', p2 = 1000 kg/m and 12000kg/m h,=0.6 m P1 h,=0.9 m P2 P3
An engineer sees a water flow through a 0.4 km long and 200 mm diameter pipe having a roughness of 0.0015 mm at 0.075 cubic meter per second. Assuming that the property of H2O is u = 0.001 Nm/sec and p = 1 g/cu.m. He is bored, so he wanted to calculate the following, help him. a. the pressure drop cause of friction b. velocity of H2O in the pipe c. find the Re?
2. If the Patm = is 101.3KP and the Pabs at the bottom of the tank is 231.3 kPa. y of H20 = 9.79KN/M^3 SAE Oil (0.89) 1.5m Water 2.5m Olive oil 2.9m Mercury (13.6) 0.4m 1. Determine the specific gravity of the olive oil. 2. What is the absolute pressure at the interface of the olive oil and the mercury? 3. What is the gage pressure at the interface of the olive oil and the mercury?
Q2: A plate having an area of 0.6m² is sliding down the inclined plane at 30° to the horizontal wi a velocity of 0.36m/sec. There is a cushion of fluid 1.8mm thick between the plane and the plate Find the viscosity of the fluid if the weight of the plate is 208N.
2) An open cylindrical tank contains 2 liquids with specific gravities and depth as follows: Liquid 1: Sı=1.00 di=1.30m; Liquid 2: S2=1.50 d2=1.35m; Liquid 2: S2=1.50 d2=1.35m. Find the pressures along the interface of the liquids and at the bottom of the tank.
In a given setup, distilled water flows towards the inside and goes outside of the vessel as shown in the figure. What is the rate of change of the water's mass (dm/dt) in the vessel? 3 in. Q = 0.3 ft3/sec V = 30 ft/sec Device m = 0.3 slug/sec %3D
mechanics of deformable bodies with solutions
A flow of liquid is discharged from a long horizontal pipe of circular cross-section into theatmosphere. Sketch the typical appearance of(i) a laminar jet(ii) a turbulent jet.Explain their forms and the differences between them.Define the loss coefficient K, used in the analysis of pipe systems. Give three examples of distinct elements in pipe systems which lead to losses, explaining briefly in each case why the losses occur.You want to draw water from a stream running down a hill behind your house at a rate of 3 litres /s.To hand you have 30m of commercial steel tubing of inside diameter 30mm. At what vertical level above the house should you dam the stream to draw off the water?.
For flow in a pipe with Reynolds number of Re=10^7: