H In fig find the force of the water of the tank bottom, if H=2 m, width= 1.5 m and long (into the paper= .3m P. Z ↓↓ Liquid PB atm ↓↓↓↓ 88200 lb O 88200 KN 88200N

Q: FIND PA - PB

A:

Q: a. Compute the bulk modulus of elasticity. b. Compute the percentage of volume decreas c. Compute…

A:

Q: The 39-kg crate is stationary when the force P is applied. Determine the resulting acceleration of…

A: Given data:

Q: 5. A dam with 4 meters on top, 10 m at the bottom and 20 meters high has water with depth of 15…

A: This question is related to the Soil Mechanics.

Q: Sketch a flowchart showing the steps involved in the analysis of: Flexure in Doubly Symmetric Shapes…

A: We need to create a flowchart to explain how to build structural steel beams with doubly symmetric…

Q: 150 kW 4m A, TLT 4m 4m E 4m T 100kw 200 kas

A: Consider the diagram of the truss as shown below.

Q: graphical method to construct the shear-force and bending-moment diagrams for the be = 21 kN, w = 45…

A:

Q: ਕਰ ਸ Elementos TAB = TBC = TBD TAD = TDC = TED= 6m 135 kN B D ( ) ) 6 m 67.5 kN 1.5 m 1.5 m 1.5 m…

A:

Q: Consider two identical springs. This means that the two springs are made of the same wire, have the…

A: Energy stored in spring is given byEs=32P3R3nGd4R=L2πn

Q: For the beam section shown in figure, calculate the maximum load that the beam can carry without…

A:

Q: RN, and a force, F= 66 KN) inclined at an angle alpha = 30 degrees from the vertical, such that it…

A:

Q: Stress analysis Task Question / Calculate the critical design loads applied to the Stirling Engine…

A: Please find the answer in the below attachments

Q: the reaction by the bend FrY (N).

A:

Q: How much of an increase in Fc is gained for a steel column whose end is changed from pinned-pinned…

A: When a steel column's end conditions change from pinned-pinned to fixed-fixed,Fc increases by a…

Q: A circular nylon [E = 8 GPa; v=0.35; a=20x106/°C] disk with a circular hole in its center is shown.…

A:

Q: Assume that F = {28i-42j+47k} lb (A) Determine the magnitude of the component of F acting along the…

A:

Q: Question 7 7.Value of shear at midspan in Ib. b=3.17 inches h=5.62 inches P= 1657 lb A= 3.75 ft B=…

A: Question is based on the simply supported beam subjected to point load .Magnitude of load and span…

Q: a particle moves m a circular puth f. 15-M hadius sf tfat its are distan ce from a fixed point on…

A:

Q: Show full solution

A:

Q: The piston rod of diameter 20 mm and length 700 mm in hydraulic cylinder is subjected to compressive…

A: Given data- Diameter d=20 mm, Length L=700 mm, Force P=10 kN, Young's modulus E=200 GPa, To Find-…

Q: Betermine the volume V and total surface area A of the solid generated by revolving the area shown…

A:

Q: A bar AE is in equilibrium under the action of the five forces shown. Determine P (kN). F1 = 85 kN…

A:

Q: 100 lb 50 Ib 45 250 lb 2. Determine M, P, and Q in the figure shown so that the resultant of the…

A:

Q: A 4m slope failed nearby congested urban road. The structure on the top of the slope contributes to…

A: A retaining wall is generally a huge structure that is made to keep a hill and slope of the earth…

Q: 3. Determine the normal force between the crate and the surface 4. Determine the force P needed to…

A: Given- W = 856 N Frictional coefficient - μs = 0.3 height of block = h = 2 m Width of block = b = 1…

Q: A 10 il load is uniformly cated by an aluminum alloy pipe with an outside diameter of 10 cm and…

A:

Q: B-A thickener is designed to separate suspension containing 15 Kg of water/Kg of solid is to be…

A:

Q: Q- The surface area of a plate is 0.4 m² and its weight is 500 N which slides down on an inclined…

A: Given- Surface area A=0.4 m2Weight of plate W=500 NSpeed of sliding plate V= 4 m/sDynamic viscosity…

Q: na horizontal pipe, which of the following is constant?

A:

Q: Surface Nozzle Fluid stream F1 Surface Nozzle Fluid stream F2

A: Write the component of force F1 in x-direction. F1=-ρA1V121-cosθ=-ρA1V121-cos90°=-ρA1V12 Write the…

Q: In fig find the force of the water of the tank bottom, if H=2 m, width= 1.5 .m and long (into the…

A: This question is related to the Fluid Mechanics.

Q: Prove that poison ratio is less than(<) than half(0.5)

A: Poissions ration is less than 0.5 and proof is given below

Q: W C hz В D D D hi E E L System 1 System 2 System 3

A: The given data is: w= 50 kN/m h1 = 4 m h2 = 2 m L =12 m System 1 = Fixed arch System 2 = Two hinged…

Q: 120 kN/m 35 12 kNm 24 kNm 6 kNm 6 m 2 m 1 m RA Rg EMA = 0 = ??? Rg =353 kN %3D Unit of M = kNm RB =…

A:

Q: all expressed as CaCO3. Determine the chemical dosages required to soften this water as much as…

A:

Q: A Pipe specific gravity pressure of 110 kN/ m² and pipe B contains oil of specific gravity A…

A:

Q: seed

A: Force due to weight of glassFg=γ2πrth=2.6×9.81×2π×0.052×0.005×0.1Fg=0.00063765π kNForce due to…

Q: 1. Show that: GE (a) k = 9G-3E 3k-2G (b) v = 6k+2G

A: