A cylindrical tank with hemispherical heads is constructed of steel sections that are welded circumferentially (see figure). The tank diameter is 1.0 m, the wall thickness is 30 mm, and the internal pressure is 6 MPa. Determine the maximum shear stress in the head of the tank. Welded seams Lütfen birini seçin: a. None b. 51.56 MPa c. 25.00 MPa d. 48.75 MPa e. 62.50 MPa

A cylindrical tank with hemispherical heads is constructed of steel sections that are welded circumferentially (see figure). The tank diameter is 1.0 m, the wall thickness is 30 mm, and the internal pressure is 6 MPa. Determine the maximum shear stress in the head of the tank. Welded seams Lütfen birini seçin: a. None b. 51.56 MPa c. 25.00 MPa d. 48.75 MPa e. 62.50 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is the stress in the pipe when there is no internal pressure What is the maximum permissible internal pressure in the pipe if the working tensile stress in the brass is 60MPa
A rectangular plate (0 =20°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.0 MPa in the x-direction and a tensile stress of 10 MPa in the y-direction. Determine the normal and the shear stresses acting parallel to the weld. y Weld Lütfen birini seçin: a. -0.417 MPa/4.38 MPa O b. 9.3175 MPa/5.50 MPa O c.-0.596 MPa/3.85 MPa d. None e. 8.5962 MPa/3.85 MPa
Emmii DH Tube Corrugated Tube DH P (mm) e (mm) 25 7 1.5 0.013 Find the equivalent diameter 11:06
The aluminium and Steel pipes are fastened to rigid supports at one of their ends and to a rigid plate C at others end derive expression for axial stress in the two pipes
How many 8-mm diameter rivets is needed to fasten member DC to the gusset plate at Cif the member DC has thickness of 8 mm and the working stresses are 15 MPa for shear in the rivets and 20 MPa for bearing due to the rivets. Express your answer to the nearest whole number being the safe value of the rivets to be used. * Sm 40 RN 35 AN
known. Using simple measurement tools, the following features are measured. A spring is known to be made from music wire, ASTM A228 steel, however no other data are Free length of the spring was 44.45 mm. Outside Diameter was 14.25 mm Wire diameter was 1.4 mm The ends are squared and ground The total number of coils was 10.0 This spring will be used in an application where the normal operating load is to be 62.28 N. (Take 1 inch = 25.4 mm) a) Determine the inside diameter, spring index and Wahl factor. b) Determine the expected stress at this operating load. c) Determine the spring deflection at the normal operating load. d) Determine the operating length, solid length and the spring rate. e) Determine the coil clearance and check the spring against buckling. Datermine the minimum hole diameter for the spring to operate in.
A tensile load of 330,000 N is applied to a copper pipe with maximum allowable stress of 110 MPa and 80 mm inner diameter. What should be the thickness of the pipe? Choices: A. 9.78 mm B. 12.35 mm C. 11.56 mm D. 10.55 mm
A cylindrical tank with hemispherical heads is constructed of steel sections that are welded circumferentially (see figure). The tank diameter is 1.1 m, the wall thickness is 32 mm, and the internal pressure is 12 MPa. Determine the maximum shear stress in the cylindrical tank. Welded seams Lutfen birini seçin 8.75.89 MPa b. 62 50 MPa C. None d. 22.67 MPa e 103 13 MPa
10.5 (B) A compound tube of 300 mm external and 100 mm internal diameter is formed by shrinking one cylinder on to another, the common diameter being 200 mm. If the maximum hoop tensile stress induced in the outer cylinder is 90 MN/m² find the hoop stresses at the inner and outer diameters of both cylinders and show by means of a sketch how these stresses vary with the radius. [90, 55.35,-924, 57.8 MN/m²]
Calculate the wall thickness required for a thin-walled cylindrical pressure vessel which must withstand an operating internal pressure of 3.5 MPa at an outside pressure of 2 MPa. The mean diameter is 200mm and the stress must not exceed 60 Mpa. O a. 8.3 mm O b. 2.5 mm O c. 3.3 mm O d. 5.83 mm O O
MPa) which requires at least a pressure of 10 MPa to prevent leakage. Problem 8.5 A joint in the figure uses a compressed asbestos gasket (E-480 Dimensions are in mm 10 20 200 100 D 150 The cover plate is tightened by using 8, metric grade 5.8, M10x1.5 bolts. If the cylinder is to be rated for an internal pressure of 3500 kPa, calculate the necessary tightening force per bolt for a factor of safety of 2.
A welded steel girder having the cross section shown in the figure is fabricated of two b-180 mm*tf25 mm flange plates and a h=600 mm*tw3D15 mm web plate. The plates are joined by four fillet welds that run continuously for the length of the girder (1=1.15x10° mm“). Each weld has an allowable load in shear of 810 kN/m. Calculate the maximum allowable shear force Vmax for the girder. tw Lutfen birini seçin a. 1.32 MN b. 1.31 MN