Assignment 2 E B to A SkN 5kN SKN Calcu late Porcej h each men ber of tmuss, Use method of jo ch ts.

Q: Calculate to the correct number of significant figures. (3.14x2.4367) - 2.34

A: The problem is given as, In this, it can be seen that the minimum significant figure of the number…

Q: Determine Iy. 50 mm 50 mm 300 mm 50 mm y -200 mm an -X We Problem 4

A:

Q: 2. If Tc= (-5) find TF. TK and TR.

A: Given:  TC=-5

Q: Q1/ A. Write the force system for each one of the following? JIL

A: Given:-  To Find:-  Type of force system

Q: please solve the  equations in steps ()i and ()ii

A:

Q: X 300 mm D 800 mm B

A:

Q: In the figure shown, compute the following : 75 mm 75 mm E 75 mm-

A: Given Shaded area To find Centroid X axis Centroid Y axis

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: Consider a virtual load Q, acting vertically downwards, is applied at point A.Draw the given truss…

Q: 400N 200 Z00 N さ

A: Given Data :

Q: This answer is incorrect. Can someone else help me solve this again ?

A: given data

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Answer:

Q: Write the four different types of Resultant Loadings?

A: Loading: The loading on the beam or any members is the load acting on a beam under which beam…

Q: Question 18 Simplify (−4 − 4j) O 1.412-45° O 1.41/225° O 1.414-225° O 1.41/45°

A: Simply the above expression

Q: 3

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: A plastic rod AB of length L = 520 mm has a diameter d, = 30 mm as shown in Figure Q2(b). A plastic…

A: For the given composite bar it is required to determine: (1) Total elongation of the bar when P = 15…

Q: Question 24 In the same setup as in question 23, if the mass of the crane arm (including winch) is…

A: Solution for Question 24: Given, Mass of arm = m = 100 kgWeight of arm = W = mg = (100) (9.81) = 981…

Q: Q 4/ Give the names of the components to the parts in the vehicles According to the figures. Cutch 4…

A: Data given-

Q: of the table) and free to move if a force is applied. A force is applied on it as the arrow…

A:

Q: X 300 mm D 800 mm B

A: For constant angular velocity, angular acceleration is zero,

Q: Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a…

A:

Q: In the engine system shown, the lengths of the connecting rode (that is the length of BD) and the…

A:

Q: Find The curevature points A,B,C,D form least to greatest

A:

Q: Q2. (Answer One) AW-+号how tht +-0 ) "-/(). show that +-

A: Given To find prove the following

Q: The engine piston weighs 180 g. The machine speed is 4400 RPM. What is the maximum speed of the…

A:

Q: 1. The tank of the air compressor is subjected to an internal pressure of 8 bar. If the outer…

A:

Q: Determine the x-y and n-t components of the 39-kip force F acting on the simply-supported beam. F =…

A:

Q: What is the answer in #3B. Show complete solution and FBD

A:

Q: how did the equation simplify to a = 0.984?

A:

Q: If the allowable tensile stress of the wires AB and AC is oallow = 250 Mpa, determine the largest…

A:

Q: The collar A slides along the rotating rod OB. The angular position 2 of the rod is given by 0 =…

A: Given data:- thetha = 2/3 ×π t^3  rad. R = 18t^4+4 m find the velocity and acceleration vector.

Q: B A

A: Given that , m =3 kg t=0.35 s r=4 sin3θ

Q: 4 in 2 in 4 in 8 in -12 in 16 in-

A: Given data To determine the moment of inertia and radius of gyration about x and y axis

Q: Describe the Parallel-Axis Theorem for an Area?

A: