need in 30 mins. I will upvote! Two steel [E = 30,700 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.875in. and a wall thickness of 0.268 in. Pipe (2) has an outside diameter of 4.500 in. and a wall thickness of 0.229 in. Assume L₁ = 12 ft andL₂= 20 ft. If the normal stress in each steel pipe must be limited to 22 ksi, determine(a) the maximum downward load P that may be applied at flange B.(b) the downward deflection of flange B at the load that you determined in part (a).L2₂L₁Answers:(a) Pmax=(b) VB=(2)(1)MiMkPсBkipsin.

Given Data: Stress in steel, σ =22ksi Young's modulus, E = 30700 ksi For pipe 1: Length of…

Two steel [E = 30,700 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.875 in. and a wall thickness of 0.268 in. Pipe (2) has an outside diameter of 4.500 in. and a wall thickness of 0.229 in. Assume L₁ - 12 ft and L2= 20 ft. If the normal stress in each steel pipe must be limited to 22 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a).

Two steel [E = 30,700 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.875 in. and a wall thickness of 0.268 in. Pipe (2) has an outside diameter of 4.500 in. and a wall thickness of 0.229 in. Assume L₁ - 12 ft and L2= 20 ft. If the normal stress in each steel pipe must be limited to 22 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Knurling operation is done for )1 نقطة( Sizing purpose O Cutting purpose O Gripping purpose O
12 2X 011 40 25- 12 08 v 014.5X 62 12 R10 20 30 35 7 D 25 12 105 026 15- 07 V012X 829 58 Ø12 AD R12 Ø3 THRU 25 R12 09 L015 18 28 18 18- 25 120 SECTION A-A SECTION B-B SECTION C-C Ø12 V 20 U018 65 3X 012.5 20- R15 T 8 R12 25 20
The thickness of the chip in up milling is at the beginning of the cut. Select one: a. Zero b. No cutting C. Minimum d. Maximum
1. Explain with a sketch any 4 different types of centers used on a lathe machine?
10
35
List three benefits of holding a workpiece between centers
Make a steps on how to center the cutting tool with the lathe center line.
why the number of disk is 17-1?
With neat sketch explain the tap drill nomenclature?
Q6: A-List the characteristics of screw thread. B- Calculate the change gears for cutting 16 thread per inch on a lathe having a lead screw of 6 thread per inch?
Briefly describe the meaning of spark gap in wire cut machining by drawing a sketch.