The weldment shown in the figure is subjected to a static force of 100 kN. The hot-rolled steel bar has a thickness h=6 mm and is of AISI 1015 HR steel. The vertical support is AISI 1015 HR steel. The electrode is given in the table below. Use the welding code method. (a) Is the weld metal strength satisfactory? (b) Is the attachment strength satisfactory? h h=6 mm b=60 mm d=90mm electrode=E6010 ko h F

The weldment shown in the figure is subjected to a static force of 100 kN. The hot-rolled steel bar has a thickness h=6 mm and is of AISI 1015 HR steel. The vertical support is AISI 1015 HR steel. The electrode is given in the table below. Use the welding code method. (a) Is the weld metal strength satisfactory? (b) Is the attachment strength satisfactory? h h=6 mm b=60 mm d=90mm electrode=E6010 ko h F

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter4: Shielded Metal Arc Welding Of Plate

Section: Chapter Questions

Problem 25R: Can a tee weld be strong if the welds on both sides do not have deep penetration? Why or why not?

See similar textbooks

Related questions

Q: Q1: The weldment shown in the figure is subjected to a force F. The hot-rolled steel bar has a…

Q: Problem 3.1: Determine the design strength of a 1 mm length of a 6.35 mm fillet weld formed by the…

A: Given Data:Find:Determine the design strength in all the cases.

Q: E70XX 1/4 V2 1/4 For the welding information shown, calculate the design capacity of the weld Rweld…

Q: The arm in the figure is combined with a rod with a diameter of d=30 mm and a neck (corner) weld…

Q: 7) For double side parallel fillet weld subjected to an external force 100 kN. The weld has throat…

A: For condition of fillet design - F = 2×0.707×t0.707×l×τ100×1000 = 2×t×l×1001000 = 2×5×ll = 100 mm

Q: The weldment shown in Figure 2 is subjected to an alternating force F. The hot-rolled steel bar is…

Q: Q3 (a) What are the methods used to obtain a good weld when welding steel when the carbon content is…

A: Force ,F=60000 lbAllowable stress,Size of the weld ,h=1/4 inchTo determine:a)the method used to…

Q: Situation 2: The lap splice shown will develop a full strength as shown in the figure. Using E70…

A: A design method that is purposed in structural engineering and may be used for various engineering…

Q: Two plates, 25 mm thick, are welded together by means of transverse-fillet welds. TI ultimate…

A: Given : t=25 mmσu=415 MPaKs=0.85Ksf=0.5R=90%FOS=2P=100 kNA=10 mm

Q: 1/2-inch thick steel bar is welded to the vertical support A) Calculate the allowable load if the…

A: Given data as per the question h = 3/16 = 4.7625 mm d =4'' = 101.6 mm L =12''=304.8 mm

Q: The Figure shows a 0.75-in-thick AISI 1020 HR steel bar subjected to a load of (F = 1.4 kip) and…

A: Given: σy=30kpsi b=d=2in h=5/16in Load (F)=1.4kip Solution: Due to the symmetry of the weld joints,…

Q: Нome work 1. A plate( 100 mm) wide and (10 mm) thick is to be welded with another plate by means of…

A: Image_1

Q: The design below is used for a bridge construction. All parts of the assembly are made of ASTM A36…

A: P = 4000 lbOD = 4.5 inL =20 inTo find : Minimum size of weld according to table 20-4

Q: 4. A steel cylindrical vessel 2m in diameter has a wall thickness of 20 mm. the longitudinal join of…

A: The working pressure is P=0.6 MPa. The diameter of the vessel is d=2 m. The thickness is t=20…

Q: Draw the weld symbol for the following welded joint in Figure 1. 6 09 (a) 6 (b) (c) Figure 1 6

Q: Using SMAW process, E70 electrodes and an A572 steel. Determine the length of the side fillet welds…

Q: (6) The weldment shown in the figure is subjected to an alternating force F. The hot-rolled steel…

A: The fatigue load F the bar will carry if three 6 mm fillet weld are used. Given : The thickness of…

Q: 1. A bracket is shown in the figure. Calculate the stresses on the welding. The bracket welded by…

A: Given: The load is 7.5 kN. The other dimensions are shown below:

Q: shielded metal arc welding operation is performed on steel at E= 30 volts and / = 225 amps. The heat…

A: Given Voltage, E = 30 V Current, I = 225 amps Melting energy, U = 10.2…

Q: An axially-loaded welded angular connection is shown SD-002 . The angular section 150 x 100 x 10 mm…

Q: (1) What are the methods used to obtain a good weld when welding steel when the carbon content is…

A: 1. to determine the method used to obtain good weld for high carbon steel

Q: 8. Design the length of weld (L) in the connection below to develop the full tensile capacity of the…

A: given t=38inch=9.525mmwidth of plate, w=6inch =152.4mmsecond palte thickness…

Q: A steel pipe weighing 500 kg with a wall thickness of 7.5 mm is placed on the body as shown in the…

Q: Te - Effective throat thickness well in mm = 6 sin45° Consider the following drawing in which…

A: WeldExplanation:Step 1:Step 2:Step 3: Step 4:

Q: 3.) The diagram below shows a 5.5m long double angle brace which is connected by 6mm welding…

A: given data

Q: Arectangular cross-section bar is welded to a support by means of fillet welds as shown in Figure…

A: Fillet weld It is a joining process of two metal pieces when they are perpendicular or at an angle…

Q: 2. A G10200 HR steel bar of thickness h is welded to a vertical support of the same material as…

A: h= 5 mmb= 50 mmd= 50 mmMaximum shear stress of this material, y = 100 Mpa (approx)

Q: An angle iron made of AISI 1040 CD steel is welded to metal as shown and loaded with a dynamic load…

A: Material AISI 1040 CD Propoerty: Sut = 590 MPa, Sy = 490 MPa Welding material property: Sut = 482…

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

The weldment shown in the figure is subjected to a static force of 100 kN. The hot-rolled
steel bar has a thickness h=6 mm and is of AISI 1015 HR steel. The vertical support is AISI
1015 HR steel. The electrode is given in the table below. Use the welding code method.
(a) is the weld metal strength satisfactory?
(b) Is the attachment strength satisfactory?
h
h=6 mm b=60 mm d=90mm electrode=E6010
|-b-
h
F

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Show your full work. Don't provide the wrong solution.
A bracket to be welded into a steel channel using E-60 electrode 345 Mpa) Two welding sets are suggested as shown in Fig. (1)Based on maximum shear stress failure theory and safety factor of (2.5) (a) Find the weld size for each set. (b) Which set would you recommend A or B ?
Q1-A shielded metal arc welding operation is performed on steel at E = 30 volts and I = 225 amps. The heat transfer efficiency fi= 0.85 and melting efficiency f₂=0.75. The unit melting energy for steel Um = 10.2 J/mm3. Solve for: (a) the rate of heat generation at the weld and (b) the volume rate of metal welded
Solve correct
strength of materials
Assume that two 1.5-mm thick steel sheets are being spot welded at a current of 4000 A and current-flow time is 0.3 s. Using electrodes 5 mm in diameter, estimate the amount of heat generated and the amount of heat required to melt the weld nugget. Use an effective resistance of 350 un. Take u= 9,7 Joule/mm Which one of the following are correct? O a. If the electrodes were 7 mm diameter, the amount of heat generated would decrease b. The amount of heat generated by the equipment is between 1600 to 1700 Joules c. The equipment has enough power to weld the steel sheets. d. The equipment does not have enough power to weld the steel sheets e. The amount of heat required is between 700 and 750 Joules
Please show work correctly,if not sure skip.
Material Strengths: Fy = 248 MPa, Fu = 400 MPa Method: Use ASD. A single angle L127X89X19 is welded (longitudinal and transverse welds) on one leg (shorter leg) togusset plate; thus, there are no holes. The length of the longitudinal welds is 150 mm. Which of the following most nearly gives the allowable tensile load?
A continuous fillet wild is used to weld two pieces of 7.0-mm-thick austenitic stainless steel plate in an arc-welding operation. The plates are joined at a 90° angle using an inside fillet corner joint. The velocity of the welding head is 6 mm/sec. Assume the cross section of the weld bead approximates a right angle isosceles triangle (a right triangle with the two legs and their corresponding angles equal) with a leg length of 4.5 mm. The length of the weld = 230 mm. The melting factor of the setup = 0.65, the heat transfer factor = 0.90, and the Tm for austenitic stainless steel = 1670°K. Determine (a) The amount of heat (in joules) required to melt the volume of metal in (b) The heat that , (c) The rate of heat generation required at the welding source to accomplish the weld this weld (filler metal plus base metal) must be generated at the heat source
The below Figure Q1 shows an aluminium alloy sheet metal requires to be spot welded. In order for the weld to achieve its required strength, it has to be 2mm thick and the weld duration will be set at 0.3 sec. If it is assumed that the electrical resistance between the surfaces is 160 micro-ohms, and that only 40% of the electrical energy generated will be used to form the weld nugget (the rest being dissipated into the work), determine: a) The heat energy generated at the source b) The minimum current level required in this operation c) Assuming the heat transfer factor is 0.9, what would the melting factor be? d) The power density of the process, and comment on the value.
Draw the weld symbol for the following welded joint in Figure 1. 6 2 + (a) 6 (b) 2 (c) Figure 1 2 2 6 2 2
Problem 3.1: Determine the design strength of a 1 mm length of a 6.35 mm fillet weld formed by the shielded metal arc process (SMAW) and E70 electrodes with a minimum tensile strength Fexx = 483 MPa. Assume that the load is to be applied parallel to the weld length. Problem 3.2: Repeat problem 3.1 if the weld is 500 mm long. Problem 3.3: Repeat problem 3.1 if the weld is 750 mm long. Problem 3.4: Repeat problem 3.2 if the application of the load is at an angle of 35 degrees from the longitudinal axis of the weld. Problem 3.5: Repeat problem 3.3 if the application of the load is at an angle of 35 degrees from the longitudinal axis of the weld.