A steel pipe weighing 500 kg with a wall thickness of 7.5 mm is placed on the body as shown in the figure. originated. The weld seam is produced with equal forces of 5000 N in two different directions in the directions shown in the figure. drawn in the direction. The welding quality factor is the 2nd quality, ie 0.80, the safety coefficient is 1.85 and the welding flow strength of 225 N / mm2 check the safety of the source (g = 10 m / s2 ) force: 5500 N

Q: A static load of 30 kN is applied at the cantilevered beam as shown in the Figure 3.1 The cantilever…

A:

Q: The arm in the figure is combined with a rod with a diameter of d=30 mm and a neck (corner) weld of…

A:

Q: Q1: The weldment shown in the figure is subjected to a force F. The hot-rolled steel bar has a…

A:

Q: A steel cantilever beam is made of two T-shaped structures welded to each other as shown in the…

A: given; q=2MN/mσ=150MPalength (L)=L1+L2                  =1+.5                   =1.5m

Q: 11.6 Two 15-mm steel plates with S, = 400 MPa are butt-welded using E70 series weld- ing rods and…

A:

Q: 9-25 The weldment shown in the figure is subjected to an alternating force F. The hot-rolled steel…

A:

Q: 3. Two steel plates with Sy = 45 ksi are attached by parallel-loaded fillet welds. Each weld is 5…

A:

Q: 6. Find the reactions at A and C. Weight of the bar is negligible.

A: Given: Find: The reactions at A and C

Q: The shaft in (Figure 1) is used to transmit 32 hp while turning at 600 rpm. Figure 2 in. 2.5 in. 1…

A:

Q: 1) A single parallel fillet weld of total length L and weld size h subjected to a tensile load P,…

A:

Q: Q/ Explain the following symbols of welding: ( Answer a or b:) a. 25*15(10) a7 25*15 a7 615x10 (20)…

A:

Q: Find all the information from the following weld symbol 20

A: The set of symbols which together decide the type of weld or joint that is to be made at the…

Q: Q: Estimate the size of fillet weld for the bracket shown in the figure subjected to a complete…

A: To find: The size of fillet weld. Given: The factor of safety is 2. The load is P=5000 lbs. The…

Q: In Figure 1, m=800 kg load is carried by the rope-pulley system. The reel is fixed to the fork with…

A: Given that, Mass of the load, m=800 kg,Factor of safety, FOS=6,Welded bar is 1030 Anealed steel…

Q: Hi, I need help with this question.

A:

Q: The arm in the figure is combined with a rod with a diameter of d=30 mm and a neck (corner) weld…

A:

Q: Dynamic forces F1 = 4000N and F2 = 6000N are applied to the welded part shown in the figure as shown…

A:

Q: Q: Estimate the size of fillet weld for the bracket shown in the figure subjected to a complete…

A: To find: The size of fillet weld. Given: The factor of safety is 2. The load is P=5000 lbs. The…

Q: Draw the Welding symbol based on the data given • SINGLE BEVEL BUTT WELD • Flat FACE • SIZE 45 mm •…

A: Given data  SINGLE BEVEL BUTT WELD Flat FACE SIZE 45 mm HIDDEN SIDE ALL AROUND WELD To Draw the…

Q: Q: Estimate the size of fillet weld for the bracket shown in the figure subjected to a complete…

A: To find: The size of fillet weld. Given: The factor of safety is 2. The load is P=5000 lbs. The…

Q: 1. A 10 mm steel plate is welded on a wider steel plate as shown. The weld leg, w = 12 mm. Find the…

A:

Q: Find the primary, secondary and resultant shear stress of following welding. b=2", d=2", h= 1/4".…

A: To find The primary, secondary and resultant shear stress. Given  The force F is 1000 lbf. The…

Q: what is the thickness of the weld nugget assuming it has a uniform thickness?

A: I = 11000 A R = 0.000130 ohm t = 0.25s H = I2Rt = 11,0002 (0.000130)(0.25) = 3,930 J

Q: Q3 (a) What are the methods used to obtain a good weld when welding steel when the carbon content is…

A: Force ,F=60000 lbAllowable stress,Size of the weld ,h=1/4 inchTo determine:a)the method used to…

Q: A cylindrical pressure vessel has an outside diameter of 1.5 meters, and a length of 5 meters. The…

A: Solution: Given Data: d=1.5 ml=5 mt=10 mmθ=25oσn=150 MPaτ=80 MPa   To Find: P

Q: Situation 2: The lap splice shown will develop a full strength as shown in the figure. Using E70…

A: A design method that is purposed in structural engineering and may be used for various engineering…

Q: A U-groove weld is used to butt weld 2 pieces of 7.0-mm-thick titanium plate. The U- groove is…

A:

Q: Problem 14.3.A A 4 × 4 x 2-in. angle of A36 steel is to be welded to a plate with E 70 XX electrodes…

A: Given DataSteel Fy=36ksiA=4×0.5in2

Q: 「十 a-6

A: Given:

Q: For the following configurations shown in figure below, determine the ratio of the maximum shear…

A:

Q: A bracket is as shown in figure 2. Determine the uniform weld size for the arrangement. The…

A: Write the expression of strength of parallel fillet weld. P1=0.707sl1σt    ...... (1) Write the…

Q: Compute for the total length of weld required with the given tension load, T. Tension member is…

A:

Q: in the figure is desigr t welds ae required as gh the pointsA&E

A:

Q: Material Strengths: Fy = 248 MPa, Fu = 400 MPa Method: Use ASD. A single angle L127X89X19 is welded…

A: Welding is a manufacturing method for joining materials, mainly metals or thermoplastics, by melting…

Joining Processes

It is the process of permanent or temporary joining of two metal pieces with the help of heat or pressure. Two metal parts are assembled by applying an energy source for the formation of a single unit. The obtained joined metals cannot be fragmented easily with the application of any force.