1/2-inch thick steel bar is welded to the vertical support A) Calculate the allowable load if the electrode is E7018, the bar is 1015 cold drawn steel, the support is 1020 cold drawn stee

Q: msIf we apply a compressive load to a perfectly straight steel rod that is circular in cross section…

A: Draw the schematic diagram of the circular column which is pinned at both ends and is loaded by a…

Q: What is the service life

A: Introduction: While purchasing any equipment for industrial/household purpose, one of the most…

Q: Q1: The weldment shown in the figure is subjected to a force F. The hot-rolled steel bar has a…

A:

Q: A 400 ft long elevator cable (diameter of 1 inch) is made of 4130 steel with a yield strength of 120…

A:

Q: 11. A rear flange mounted cylinder extends 14 in. under a load of 10,000 Ibf. What size cylinder rod…

A: Given       Mass, m = 10000 lbf                     = 4535 kg Extension, h = 14 in…

Q: Problem 3.1: Determine the design strength of a 1 mm length of a 6.35 mm fillet weld formed by the…

A: Given Data:Find:Determine the design strength in all the cases.

Q: Question The bar is subjected to the axial load. There is a shaded section which is oriented at 0…

A: Given:A=0.02 m2P=255 KNθ=25°

Q: Q4) The plate is supported by a 1.5-in. diameter steel bar and is subjected to two forces as shown.…

A:

Q: A 3/8-inch diameter bolt is subjected to a 2,135-lb tensile load. The bolt passes through a very…

A:

Q: The design below is used for a bridge construction. All parts of the assembly are made of ASTM A36…

A: P = 4000 lbOD = 4.5 inL = 20 inTo find:Resultant force (fR)

Q: For the following diagram, calculate the force needed to stretch the wire AB by 5%. Wire is A-36…

A:

Q: The arm in the figure is combined with a rod with a diameter of d=30 mm and a neck (corner) weld…

A:

Q: If 4 lengths of support brace are required for a job, 34 13" and 45 57 1", what is the total length…

A: Given Data⇒ Lengths of subparts is : L1=341316''L2=4578''L3=291516''L4=5714''

Q: 4. Design a welded connection to resist the loading shown below (service load). A double angle…

A: DL=30 k,LL=75 k,Wn=1.2×30+1.6×75Wn=156 kipsLoad on each angle=1562=78 kips=PAngle section…

Q: Dynamic forces F1 = 4000N and F2 = 6000N are applied to the welded part shown in the figure as shown…

A:

Q: If the working stress is limited to 25% of the ultimate stress, then the factor of safety is given…

A: Factor of Safety (FOS) is given as the ratio of ultimate stress to the working stress. FOS=Ultimate…

Q: A 5⁄8-inch-thick tension member is connected to two 1⁄4-inch splice plates, as shown in Figure The…

A: Bolts are in double shear ϕrn=24.9 kips/bolt      {from the manual table 7-1} The required strength…

Q: The figure shows a welded-arm. The arm is welded using ! normal yield strength of 393MPa. If the…

A: Given data: The given weld size from the figure is The radius of the weld is

Q: 1) If we apply a compressive load to perfectly straight steel rod that is circular in cross section…

A: We do not have an idea on which direction circular rod will buckle.    Description: The buckling…

Q: Hard drawn copper rivets are u

A: Answer: d= 0.36in

Q: The weldment shown in the figure is subjected to a static force of 100 kN. The hot-rolled steel bar…

A: (a) Calculate the weld metal strength. FW=0.7072b+dh×τallowFor electrode E6010,τallow=200…

Q: Below is an image showing two 4 mm thick sheets joint together using double rivets. If the rivets…

A: Given: Thickness of the sheet (t)=4mmUltimater shear strength of the rivet=500MPaYield shear…

Q: Two plates, 25 mm thick, are welded together by means of transverse-fillet welds. TI ultimate…

A: Given : t=25 mmσu=415 MPaKs=0.85Ksf=0.5R=90%FOS=2P=100 kNA=10 mm

Q: For the following configurations shown in figure below, determine the ratio of the maximum shear…

A:

Q: Compute for the total length of weld required with the given tension load, T. Tension member is…

A:

Q: Material Strengths: Fy = 248 MPa, Fu = 400 MPa Method: Use ASD. A single angle L127X89X19 is welded…

A: Welding is a manufacturing method for joining materials, mainly metals or thermoplastics, by melting…

Q: The design below is used for a bridge construction. All parts of the assembly are made of ASTM A36…

A: P = 4000 lbOD = 4.5 inL =20 inTo find : Minimum size of weld according to table 20-4

Q: 4. A steel cylindrical vessel 2m in diameter has a wall thickness of 20 mm. the longitudinal join of…

A: The working pressure is P=0.6 MPa. The diameter of the vessel is d=2 m. The thickness is t=20…

Q: Draw the weld symbol for the following welded joint in Figure 1. 6 09 (a) 6 (b) (c) Figure 1 6

A:

Q: B2 a) b) c) The steel tube shown in Fig QB2a which has the cross section shown in Fig QB2b is to be…

A:

Q: 1. You are to design an axially loaded member that is to carry a load of 5,000 lb. The member is to…

A: Given:

Q: 2. For the given welded bracket shown, design the required size of weld needed to resist the given…

A: To Find:The maximum force on the weld.Given:The eccentric load is the distance

Q: What is the endurance limit of welded members?

A: To find  Endurance limit.

Q: Which of the following formula generally used for low carbon steel? Electrode tip diameter = 0.10’’…

A:

Q: (1) What are the methods used to obtain a good weld when welding steel when the carbon content is…

A: 1. to determine the method used to obtain good weld for high carbon steel

Q: Two cylindrical rods, AC made of aluminum and CD made of steel, are joined at Cand restrained by…

A: The diameter of the rod AC is, The modulus of elasticity of the rod AC is, The diameter of the rod…

Q: 1)Two blocks with an inclined surface of 100 mm in length, 50 mm in width and 10 mm in thickness…

A: