An axially-loaded welded angular connection is shown SD-002 . The angular section 150 x 100 x 10 mm having an area of 2400 mm a gusset plate having a thickness of 10 mm. All steel is A 36 (Fy = 248 MPa, Fu = 400 MPa) and E (70) electrodes (Fu = 484 MPa) is shielded metal-arc welding process. Compute the value of "a" if T = 500 kN. (Please do not round-off to whole number the require use the exact (2 decimal) value.)

An axially-loaded welded angular connection is shown SD-002 . The angular section 150 x 100 x 10 mm having an area of 2400 mm a gusset plate having a thickness of 10 mm. All steel is A 36 (Fy = 248 MPa, Fu = 400 MPa) and E (70) electrodes (Fu = 484 MPa) is shielded metal-arc welding process. Compute the value of "a" if T = 500 kN. (Please do not round-off to whole number the require use the exact (2 decimal) value.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
Pr
Determine the fillet weld size required if #70 electrodes are used.
Te - Effective throat thickness well in mm = 6 sin45° Consider the following drawing in which plate 1 is welded onto plate 2 as shown for tensile and shear loading. The plates are fillet welded with a weld thickness of 6 mm as shown for a length of 150 mm. The plates have an ultimate strength of 275 MPa and the welding was done with F70 welding electrodes, which possesses an ultimate strength of 483 MPa. Consider a partial factor of safety of 1.7 for the welded joint and determine the design strength of the weld joint, both in tension (Tdw) and in shear (Vdw) due to the forces acting on it. a) Determine the design strength of the following weld in tension ( ) due to vertical forces. b) Determine the design strength of the weld in shear ( ) due to horizontal forces. Attached pic is shear equation for calculation Tension equation for calculation is: Tdw = FyLwte /Ymw
11.16 Two 20-mm steel plates are butt-welded together. Both the plate and the welding electrode materials correspond to strength properties of Su = 500 MPa and S, = 400 MPa. The imposed loading fluctuates rapidly between -20 and +60 kN. Estimate the length of weld required in order to provide a safety factor of 2.5: (a) If the weld reinforcement is not removed. (b) If the excess weld material is carefully ground off to provide smooth, continu- ous surfaces.
4) Determine the maximum stress. in the welds an if the joint.is. Safe for T=90.N/c. for figurea te h= {mm ム=6mm Ans: て 300N 15cm 5cm 20 Cm 18Cm
5. A steel cylindrical air receiver with 5 feet diameter and pressure load of 180 psi, design stress of 9500 psi maximum. The pressure vessel is to be provided with a 1.5 in diameter drain valve installed at the bottom of the vessel and a safety pressure relief valve is installed either at the topmost or at the side with a pop-out rating of 200 psi. Assume a 100% weld joint efficiency. The lap welding tensile strength is 65,000 psi. Determine the bursting pressure of this air receiver. psi
Not yet answered Marked out of 1.00 P Flag question Arectangular cross-section bar is welded to a support by means of fillet welds as shown in Figure below. Determine the size of the welds, if the permissible shear stress in the weld is limited to 75 MPa. 25 kN 500 -150- 100 All dimensions in mm
i need the answer quickly
A 50 mm diameler solid shaft is welded lo a flat plate by 10mm fille: we d The maximum lorque that the welded joint can Sustain if the maximum shear stress intensity in the weld malerial is not to exceed 80 N/mm?, will be
An angle iron made of AISI 1040 CD steel is welded to metal as shown and loaded with a dynamic load varying between +40kN and +60kN. E70XX (Sut = 482MPa, Sy = 393MPa) will be used as the welding electrode. Find the factor of safety of the weld zone. Note: that both static and dynamic loads are applied to the source.
A welding fabricator welds mild steel attachments to AISI 304 stainless steel shells, using GTAW with ER309L filler wire. A helium-based shielding gas (90% He-7.5%Ar-2.5%CO2) is used, but the high cost of this shielding gas is becoming an obstacle. To reduce costs,