A 20 mm diameter bet having a diameter at the toot ef the thread of 18.6 mm is used to fasten two timhert as show in the figure. The mut is tightened to cause a tensile lm Ind on the bolt of 34 KN, Determine; a) Chearing Stress in the head of the boit b) the shearing stress in the threads C) The putside diameter of the warher if the inside dionete is 28mm and the bearing stress is limited to G MPa. 12 mm 16 mm

A 20 mm diameter bet having a diameter at the toot ef the thread of 18.6 mm is used to fasten two timhert as show in the figure. The mut is tightened to cause a tensile lm Ind on the bolt of 34 KN, Determine; a) Chearing Stress in the head of the boit b) the shearing stress in the threads C) The putside diameter of the warher if the inside dionete is 28mm and the bearing stress is limited to G MPa. 12 mm 16 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ASAP
I need handwritten otherwise skip all parts with option or I'll dislike
Please answer ASAP in 3 decimal places, need within an hour, thank you!
A flange bolt coupling is used to connect two solid shaft 125 mm in diameter. If the shearing stress is 85 MPa, how many 12 mm bolts must be used on a 250 mm diameter bolt circle to carry the load? (Round up to whole number)
For the joint shown in the figure, if F = 28 kN and dn = 12.8 mm, calculate: 7.5 mm F F 12 mm 12 mm 7.5 mm - de - F 18 mm - F 18 mm 125 mm 1. The largest bearing stress in MPa between the pins and the members; a. 146.23 MPa b. 182.29 MPa c. 174.56 MPa d. 199.37 MPa 2. The average shear stress in MPa in the pin and; a. 108.80 MPa b. 116.14 MPa c. 136.23 MPa d. 98.01 MPa 3. The largest average normal stress in MPa in the members. a. 181.23 MPa b. 175.76 MPa c. 191.26 MPa d. 150.32 MPa
3) For a single thread M16, the thread pitch p=2mm, the minor diameter d1=13.853mm, the pitch diameter d,=14.71mm, Find the lead angle y ?
NEED ANSWER ASAP THANK YOUU The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the pin in psi if a load of P = 20144 lb is applied at A? The d = 0.79-in.-diameter pin is in double shear. Round off the final answer to two decimal places.
SITUATION 2: Find the smallest diameter of bolt and the minimum thickness of each yoke that can be used in the clevis shown in the figure below if P = 400 KN. The shearing strength of the bolt is 300 MPa and the bearing strength is 500 MPa. € Yoke
Question 1 double-shear pin connections at Band D. All pins are 7 mm in diameter. a = 750 mm, b = 350 mm, h= 550 mm, P= 725 N, and 8 = 55° Determine the shear stress in pin B. Answer in MPa rounded-off to 2 decimal places. (1) a b P
3 holes with a diameter of 34 mm will be drilled at the same time in the steel sheet material with a shear strength of 340 MPa. Hair thickness According to 2 mm, the press force required to be applied by the Staples is MN as follows what are they? Please select one: A.2,18 B.21,8 C.0,218 D.0,436 E.4,36
(5) A gas engine valve spring is loaded to 35kgf when the valve is closed & 52kgf hen the valve is open. The valve lift is 8mm. The outside diameter is to be from 38mm~45mm, & the permissible stress is 413N/mm2 . Determine: (a) the wire & outside diameter; (b) the number of effective coils; (c) the free length when it is squared & ground.
1. Kindly solve this and show your solution.