In the clevis shown in Figure 4.3, find the maximum bolt diameter and the minimum thickness of each yoke that will support a load of P=14 kips without exceeding a shearing stress of 12.15 ksi and a bearing stress of 20.15 ksi. Figure 4.3

In the clevis shown in Figure 4.3, find the maximum bolt diameter and the minimum thickness of each yoke that will support a load of P=14 kips without exceeding a shearing stress of 12.15 ksi and a bearing stress of 20.15 ksi. Figure 4.3

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.10P: A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a...

See similar textbooks

Related questions

Q: The round shaft shown below is subjected to an axial impact/shock direct tensile load of F = 50000…

A: It is given that the stress at groove and the hollow part is equal, thus we will first look at the…

Q: 4. Solve problem 8.10 in our textbook (find the safety factor for failure at the fillet). Note that…

Q: The five-bolt connection must support an applied load of P= 196 kips. If the average shear stress in…

Q: The tensile load on the bar mentioned varies from 4,000 lb to a minimum of 1,200 lb. Rapid cycling…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

Q: A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has…

Q: 1) Ball bearings support the rotating axle shown below at points A and D. The rotating axle is…

A: Treat the shaft as simply supported beam with supports at A and D.Here are reaction forces at…

Q: Calculate the maximum tensile stress developed in a 1/4-20 bolt (Major dia = 0.2500" and Root dia =…

A: Write the given data with suitable variables: P=426 lbdmin=0.1959 in

Q: Onv Problems 9-29 to 9-32 F 9-29 to 9-32 A steel bar of thickness h is welded to a vertical support…

Q: Suppose the load in the figure below is 2 kN. Further suppose that the distance between the load and…

A: Given : P= 2kN The distance between load and centroid is 1.3 m The horizontal distance between bolt…

Q: 2. Calculate the shear stress in a simple pin joint, assuming pin diameter of 10 mm and 3550N…

Q: a total width of 48mm. The pin has an diameter of 11mm.....

A: GIVEN:dia of pin 11mmthickness t=16mmwidth b=48mmtensile stress =60mpabearing stress=70mpashear…

Q: The figure shows a bar with a point load of 22 kN applied at the free end, the other end of the bar…

A: Given data: F=22 kNd=6 mm Need to determine the shear stress in the bolt.

Question

In the clevis shown in Figure 4.3, find the maximum bolt diameter and the minimum thickness of
each yoke that will support a load of P=14 kips without exceeding a shearing stress of 12.15 ksi
and a bearing stress of 20.15 ksi.
Figure 4.3

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Concept of shearing and bearing stress.

VIEW

Step 2 Calculation of diameter and thickness.

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
An inflatable structure used by a traveling circus has the shape of a half-circular cylinder with closed ends (see figure). The fabric and plastic structure is inflated by a small blower and has a radius of 40 ft when fully inflated. A longitudinal scam runs the entire length of the "ridge" of the structure. If the longitudinal scam along the ridge tears open when it is subjected to a tensile load of 540 pounds per inch of seam, what is the factor of safety n against tearing when the internal pressure is 0,5 psi and the structure is fully inflated?
A lifeboat hangs from two ship's davits. as shown in the figure. A pin of diameter d = 0.80 in. passes through each davit and supports two pulleys. are on each side of the davit. Cables attached to the lifeboat pass over the pulleys and wind around winches that raise and lower the lifeboat. The lower parts of the cables are vertical and the upper parts make an angle a =15° with the horizontal. The allowable tensile force in each cable is 1800 lb, and the allowable shear stress in the pins is 4000 psi. If the lifeboat weighs 1500 lb, what is the maximum weight that can be carried in the lifeboat?
Provide FBD and solution.
For the following problem please show intermediate steps including free body diagrams, equation used, problem setup etc. so that your approach can be followed. Finally please put the answer in a box with the appropriate unit.
3. Calculate the bearing stress and shear stress between the pin and each bracket of a clevis joint. Assume pin diameter of 10 mm, 40 mm wide gap link, 12 mm thick bracket, and 3550N tensile load. Draw a free body diagram (geometry & forces) Identify stress plane Calculate stress and write it (with appropriate units) in the outlined box
Strictly don't use chatgpt,I need FBD.
Show only the free body diagram for each question given.
PROBLEMS: 1. A taper pin is used to fix a lever to a shaft, if it is to transmit a maximum torque of 850 in-lb. The shaft diameter is 1.75 inches and has an ultimate stress of 60,000 psi, if the factor of safety is 3, find A. Force that will shear the pin B. Shear pin diameter
In the hanger shown in figure 2, the upper portion of link ABC is 3/8 in. thick and the lower portions are each 1/4 in. thick. Epoxy resin is used to bond the upper and lower portions together at B. The pin at A is of 3/8-in. diameter while a 1/4-in.-diameter pin is used at C. Determine: the average shearing stress on the bonded surfaces at B. the bearing stress in the link at C. Figure 2 1.75 in.- 6 in. 7 in. E 500 lb B 5 in. D -1.25 in. 10 in.
Calculate the maximum tensile stress developed in a 1/4-20 bolt (Major dia = 0.2500" and Root dia = 0.1959"), 3" long, and a head height of 0.1875", if it is subjected to a load of 426 lbs.
Problem 2 only, solve carefully, include the units and dra the diagram. Thanks! A 3/4 inch diameter rivet is used to fastened two 25 mm thick plate. If the shearing stress of rivet is 80 Mpa, A. What tensile force applied each plate to shear the bolt, pounds?B. What bearing stress that the bolt can withstand, MPA