A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 208 mm and a wall thickness of 8 mm. Segment (2) has an outside diameter of 112 mm and a wall thickness of 16 mm. The shaft is subjected to torques TB = 49 kN-m and Tc = 16 kN-m, which act in the directions shown. Determine the maximum shear stress magnitude in segment (2). O 78.4 MPa 618 O 107.0 MPa O 82.6 MPa O 100.4 MPa O 62.7 MPa B Tc

A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 208 mm and a wall thickness of 8 mm. Segment (2) has an outside diameter of 112 mm and a wall thickness of 16 mm. The shaft is subjected to torques TB = 49 kN-m and Tc = 16 kN-m, which act in the directions shown. Determine the maximum shear stress magnitude in segment (2). O 78.4 MPa 618 O 107.0 MPa O 82.6 MPa O 100.4 MPa O 62.7 MPa B Tc

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 50-mm-diameter solid shaft is subjected to the distributed and concentrated torsional loadings shown. Draw the torque diagram. Calculate the absolute maximum and minimum shear stresses on the outer surface of the shaft and specify their locations, measured from the fixed end A. 1400 N·m 3000Nm/m B 1.2m 1.8m
The bell crank shown is in equilibrium. (a) Determine the required diameter of the connecting rod AB if its axial stress is limited to 120 MPa. (b) Determine the shearing stress in the pin D if its diameter is 20 mm. B 30° 260 mm- 180 mm A 3. C D 140°. DOUBLE 28 KN SHEAR
A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 236 mm and a wall thickness of 8 mm. Segment (2) has an outside diameter of 120 mm and a wall thickness of 16 mm. The shaft is subjected to torques TB = 44 kN-m and TC = 16 kN-m, which act in the directions shown. Determine the maximum shear stress magnitude in segment (2).
A compound shaft consists of segment (1), which has a diameter of 1.5 in., and segment (2), which has a diameter of 2.2 in. The shaft is subjected to a tensile axial load of P = 14 kips and torques TA = 5 kip·in. and TB = 34 kip·in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.
A compound shaft consists of segment (1), which has a diameter of 1.5 in., and segment (2), which has a diameter of 1.9 in. The shaft is subjected to a tensile axial load of P = 17 kips and torques TA = 7 kip-in. and Tg = 28 kip-in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element. TB TA ■K Answer: Point H: 0x = Txy = Point K: Txy = A (1) ■H ksi ksi ksi ksi ksi ksi B Ⓡ
A compound shaft consists of segment (1), which has a diameter of 1.0 in., and segment (2), which has a diameter of 1.3 in. The shaft is subjected to a tensile axial load of P = 16 kips and torques TA = 14 kip·in. and TB = 32 kip·in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.
A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 226 mm and a wall thickness of 8 mm. Segment (2) has an outside diameter of 128 mm and a wall thickness of 14 mm. The shaft is subjected to torques TB = 48 kN-m and TC = 17 kN-m, which act in the directions shown. Determine the maximum shear stress magnitude in segment (1).
1
len 1
The same torque is applied to two tubes with identical metal sheets, determine the ratio of Tsquare/Tcircle of the shear stresses. Given: r = 11 mm, S = 18 mm, and t = 2.53 mm. S
The copper pipe [G = 8,000 ksi] has an outside diameter of 3.625 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 95 lb-ft/ft along its entire length. Using a = 2.0 ft, b = 4.0 ft, and c = 8.5 ft, determine (a) the maximum shear stress in the pipe. (b) the rotation angle oc at the free end of the shaft. b B C Answers: ksi (a) Tmax i rad (b) Pc = i
A 0.500 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 9.3 in., and the load applied to each pulley is P = 57 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft. 3 Answer: Tmax = psi 1/3