A 0.500 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 9.3 in., and the load applied t- 57 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Det magnitude of the maximum horizontal shear stress in the shaft. В Answer: nsi 3 13 /3

A 0.500 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 9.3 in., and the load applied t- 57 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Det magnitude of the maximum horizontal shear stress in the shaft. В Answer: nsi 3 13 /3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bell crank shown is in equilibrium. (a) Determine the required diameter of the connecting rod AB if its axial stress is limited to 120 MPa. (b) Determine the shearing stress in the pin D if its diameter is 20 mm. B 30° 260 mm- 180 mm A 3. C D 140°. DOUBLE 28 KN SHEAR
asap please thank you
The rigid beam ABC is supported by a pin connection at C and by steel rod (1), which has a diameter of 7 mm. If the normal stress in rod (1) must not exceed 215 MPa, what is the maximum uniformly distributed load w that may be applied to beam ABC? What is the allowable force in road (1)? Use dimensions of a = 350 mm, b = 700 mm, and c = 525.0 mm.
Correct answer.
Problem 1: Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T=2880 N and T;=432 N. The maximum bending moment is atx= 230 mm (point B), and it equals M= 698.3 N•m completely reversed, where the torque is constant at 612 N.m at the same point. The shaft material is AISI 1020 CD steel. Take the stress concentration conditions at B to be Shoulder fillet-sharp, with notch radius r=0.6 mm (Table 7-1). y 230 mm T, 280 mm 30-mm dia. T C 300 mm 250-mm dia. 400-mm dia. 270 N 1800 N a) Sketch a general shaft layout in 2D (x – y axes), including all components and torques, then calculate all reactions. b) Based on the current shaft dimensions and using only forces at B and C, find the lowest critical speed of the shaft. c) Discard the indicated shaft diameter and use DE-Goodman criteria to determine the critical diameter of the shaft based on infinite fatigue life with a design factor n of 1.5. (Take the same value of endurance limit as that used in…
1. "ll zain IQ Qz 5 torsion.p.. Strength of materials Qz The steel shaft has a diameter of 50 mm and is fixed at end A and turn free at end B. If it is subjected to the couple, determine the maximum shear stress in regions AC and CB of the shaft. G = 75 GPa. 3 kN 3 kN 400 mm 50 mm 50 mm 600 mm
answer only letters D and E
The beam is subjected to a uniform live load of1.2 kN/mkN/m, a dead load of 0.5 kN/mkN/m, and a single live load of 45 kNkN. Assume AA and CC are roller, and BB is a short link. Follow the sign convention. The distributed live load can be applied to several segments of the beam that are not necessarily adjacent. (Figure 1) A)The beam is subjected to a uniform live load of1.2 kN/mkN/m, a dead load of 0.5 kN/mkN/m, and a single live load of 45 kNkN. Assume AA and CC are roller, and BB is a short link. Follow the sign convention. The distributed live load can be applied to several segments of the beam that are not necessarily adjacent. (Figure 1) B)Determine the maximum positive shear at EE. y D B E 4 m 4 m 4 m 4 m
5-83 The A-36 steel shaft is made from two segments: AC has a diameter of 0.5 in. and CB has a diameter of 1 in. If the shaft is fixed at its ends A and B and subjected to a uni- form distributed torque of 60 lb in./in. along segment CB, determine the absolute maximum shear stress in the shaft. 5 in. 0.5 in. 20 in. 60 lb-in./in. 1 in. B Prob. 5-83
Calculate the maximum moment (with diagram) & maximum shear (with diagram)
stion 27 1 points Save Answe A built up l-section is formed from plates welded together as shown in the figure. It is to be used as a column L = 3.5 m long. All elements are A36 steel and connected such the section is fully effective. Using the following properties, calculate the flexural buckling stress, Fer, in MPa using theoretical k. Flanges: b = 150 mm, t = 17 mm Web: h= 310 mm, tw - 7 mm Write your final answer in two decimal places only. I L tw
F5. The circular shaft AC is fixed to rigid walls at A and C. The section AB is solid annealed bronze and the hollow section BC is made of aluminum alloy 2024 T-4. There is no stress in the shaft before the 20,000 ft-lb torque is applied. Determine the maximum shearing stress in each shaft after T is applied. Section BC 4 D=4" 20 ft-k 6.5-FE B 5ft Match each item to a choice: TAB TBC 2"