A cantilever timber beam with a span of L=2.1m supports a uniformly distributed load w The beam width is b=320 mm and the beam height is h=170 mm. The allowable bending stress of the wood is 5.5 MPa. Determine the magnitude of the maximum load w that may be carried by the beam.

Q: A uniformly distributed load, W1, is applied all throughout the length of the beam and a…

A: To Determine Depth of the beam , h

Q: 5. The wood beam has an allowable shear stress of Tallow = 7 MPa. Determine the maximum shear force…

A: Given: The wooden beam shown in figure allowable shear stress = 7Mpa To determine: Maximum shear…

Q: A cantilever timber beam with a span of L = 3.8 m supports a uniformly distributed load w. The beam…

A: Using formula to find maximum bending moment

Q: A compression bar having a square crosssection with sides b 5 50 mm is subjected to load P.The bar…

A: Determine the maximum load P that can be applied to the bar?

Q: A cantilever timber beam with a span of L = 2.6m supports a uniformly distributed load w. The…

A:

Q: A cantilever timber beam with a span of L 3 m supports a uniformly distributed load w. The beam…

A:

Q: A 5 ft. long laminated wood beam is built up by gluing together three 2” x 6” boards to form asolid…

A: Draw the free body diagram.

Q: 3.) A composite beam is composed of three planks, each 150 mm by 50mm., glued together to form an I…

A: Allowable shear stress = 0.83N/mm2

Q: 2. Determine the minimum dimension h to the nearest mm of the beam's cross section to safely support…

A:

Q: A cantilever timber beam with a span of L = 3.5 m supports a uniformly distributed load w. The beam…

A:

Q: 75 /2 100 mm

A:

Q: 1. A single span beam having an unsupported span of 20m carries a uniform load of "W" kN/m…

A:

Q: concrete floor slab 100 mm thick is cast monolithic with concrete beam 2.0 m on centers. The beams…

A:

Q: A pair of wood components having a dimension of 100mm X 100mm is joined by means of glue as shown.…

A: angle from horizontal    θ=tan-134=36.86°shear stress on glued section ζ= 1650 Kpaand normal stress…

Q: simply supported beam is reinforced with 5-25mm at the bottom And 2-20mm at the top if the beam.…

A:

Q: A beam is fabricated by gluing four dimension lumber boards, each 40 mm wide and 80 mm deep, to a 30…

A: Given data,  Allowable bending stress = 5.7 MPa Allowable shear stress in plywood = 545 kPa…

Q: Situation 17: A rectangular beam has a width of 300mm and an effective depth to the centroid of the…

A: Given -  Width =300mm Effective depth = 600mm Tension reinforcement = 4762 mm2 Fy = 414.6Mpa and f'c…

Q: A cantilever timber bear supports a uniformly dis width is b = 340 mm and = 210 mm. The allowable…

A:

Q: maximum uniformly distributed load which can be carried by the beam on a 4 m simple span.

A:

Q: A cantilever timber beam with a span of L = 2.8 m supports a uniformly distributed load w. The beam…

A: GivenLength of beam, L = 2.8 mWidth, b = 320 mmHeight, h = 250 mmAllowable bending stress of wood =…

Q: determine the safe resisting moment of the beam in KN.M.

A:

Q: A concrete floor slab 10e mm thick is cast monolithic with concrete beams 2.0 m on centers. The…

A:

Q: A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The…

A:

Q: A timber beam 150 mm wide and 200 mm deep is to be reinforced by bolting on two flitched each 150 mm…

A: Answer We are given  Timber section 150 mm * 200 mm Steel section 150 mm * 12.5 mm Es = 20 Ew…