A cantilever timber beam with a span of L = 3.5 m supports a uniformly distributed load w. The beam width is b = 260 mm and the beam height is h = 150 mm. The allowable bending stress of the wood is 6.1 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w= L b kN/m.

A cantilever timber beam with a span of L = 3.5 m supports a uniformly distributed load w. The beam width is b = 260 mm and the beam height is h = 150 mm. The allowable bending stress of the wood is 6.1 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w= L b kN/m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cantilever timber beam with a span of L = 2.8 m supports a uniformly distributed load w. The beam width is b = 260 mm and the beam height is h = 210 mm. The allowable bending stress of the wood is 5.2 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w = i kN/m.
A cantilever timber beam with a span of L = 2.6 m supports a uniformly distributed load w. The beam width is b = 250 mm and the beam height is h= 140 mm. The allowable bending stress of the wood is 5.9 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w= i eTextbook and Media Save for Later kN/m. Attempts: 0 of 3 used Submit Answer
solve for the wind load on the right side
solve the wind load on the left side
Answer problem1
A TIMBER BLOCK “B x B” mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A “B” mm AND ‘t’ mm THICK STEEL PLATES. DETERMINE THE THICKNESS ‘t’ SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY.
The steel framework shown below is used to support the reinforced concrete slab (unit weight of concrete =23.6KN/m3) that is used for an office use (minimum live load = 2.4KPa). The slab is 150 mm thick. Use a=3m, b=5m. Neglect the self-weight of the beam and girder. Assume all beams and girders have simple supports. NSCP 2015 Load factors: 1.2DL & 1.6LL. Calculate the total ultimate/factored liveload in Kilo Pascals? Express your answer in 2 decimal places
A simply supported wood beam with a span of L = 22 ft supports a uniformly distributed load of w0 = 280 lb/ft. The allowable bending stress of the wood is 1.30 ksi. If the aspect ratio of the solid rectangular wood beam is specified as h/b = 3.00, calculate the minimum width b that can be used for the beam.
A simply supported wood beam of length L = 8 ft carries a concentrated load P at midspan, as shown. The cross- sectional dimensions of the beam are b = 7 in. and h = 13 in. If the allowable shear strength of the wood is 130 psi, determine the maximum load P that may be applied at midspan. Neglect the effects of the beam's self-weight. 12 Answer: P = IM P B 7/2 C X lb N b h
4
A simply supported wood beam with a span of L = 15 ft supports a uniformly distributed load w. The beam width is b = 7 in. and the beam height is h = 13 in. The allowable bending stress of the wood is 860 psi. Determine the magnitude of the maximum load w that may be carried by the beam. b Answer: w = i lb/ft.