A cantilever timber beam with a span of L = 2.8 m supports a uniformly distributed load w. The beam width is b = 260 mm and the beamheight is h = 210 mm. The allowable bending stress of the wood is 5.2 MPa. Determine the magnitude of the maximum load w that maybe carried by the beam.Answer: w =ikN/m.

Answered: Image /qna-images/answer/c7010033-a1e1-4f82-98be-14b05af99ded.jpg

A cantilever timber beam with a span of L= 2.8 m supports a uniformly distributed load w. The beam width is b = 260 mm and the beam neight is h = 210 mm. The allowable bending stress of the wood is 5.2 MPa. Determine the magnitude of the maximum load w that may pe carried by the beam. Answer:w- i kN/m.

A cantilever timber beam with a span of L= 2.8 m supports a uniformly distributed load w. The beam width is b = 260 mm and the beam neight is h = 210 mm. The allowable bending stress of the wood is 5.2 MPa. Determine the magnitude of the maximum load w that may pe carried by the beam. Answer:w- i kN/m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The web has a width of 350 mm and the slab thickness is 100 mm. The beam has a span of l6.5 feet and spaced at 6.5 feet center to center of the beam. A reinforced concrete T-beam has an effective depth of 500 mm and has a reinforcement bar of 8 - #7 bar size at the bottom. Yield stress of steel is Fy = 280 MPa. Concrete has a strength of f c = 20.7 MPa Assume steel covering of 40 mm. a. Determine the effective width of the flange. b. Determine the depth of compres sion block. c. Determine the ultimate moment capacity of the beam.
A timber column, 8 in. × 8 in. in cross section, is reinforced on each side by a steel plate 8 in. wide and t in. thick. Determine the thickness t so that the column will support an axial load of 300 kips without exceeding a maximum timber stress of 1200 psi or a maximum steel stress of 20 ksi. The moduli of elasticity are 1.5 × 106 psi for timber, and 29 × 106 psi for steel.
reinforced Concrete
A cantilever timber beam with a span of L = 2.6 m supports a uniformly distributed load w. The beam width is b = 250 mm and the beam height is h= 140 mm. The allowable bending stress of the wood is 5.9 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w= i eTextbook and Media Save for Later kN/m. Attempts: 0 of 3 used Submit Answer
solve for the wind load on the right side
The joist AB used in housing construction is to be made from 8-in. by 1.5-in. Southern-pine boards. The design loading on each board is placed as shown in the figure below. The allowable bending stress for the wood is Jallow 1.5 and the allowable shear stress is Tallow = 180 psi. Assume that the beam is simply supported from the walls at A and B. (Figure 1) Figure 1 ▾of 1 8 in. 150 lb L 150 lb L 150 lb L 1.5 in. Determine the largest room width I that the boards can span. Express your answer to three significant figures and include the appropriate units. L = 32.0 Submit μA ft My Answers Give Up ? Incorrect; Try Again; 3 attempts remaining
A TIMBER BLOCK “B x B” mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A “B” mm AND ‘t’ mm THICK STEEL PLATES. DETERMINE THE THICKNESS ‘t’ SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY.
The steel framework shown below is used to support the reinforced concrete slab (unit weight of concrete =23.6KN/m3) that is used for an office use (minimum live load = 2.4KPa). The slab is 150 mm thick. Use a=3m, b=5m. Neglect the self-weight of the beam and girder. Assume all beams and girders have simple supports. NSCP 2015 Load factors: 1.2DL & 1.6LL. Calculate the total ultimate/factored liveload in Kilo Pascals? Express your answer in 2 decimal places
A simply supported wood beam of length L = 8 ft carries a concentrated load P at midspan, as shown. The cross- sectional dimensions of the beam are b = 7 in. and h = 13 in. If the allowable shear strength of the wood is 130 psi, determine the maximum load P that may be applied at midspan. Neglect the effects of the beam's self-weight. 12 Answer: P = IM P B 7/2 C X lb N b h
4
A simply supported wood beam with a span of L = 15 ft supports a uniformly distributed load w. The beam width is b = 7 in. and the beam height is h = 13 in. The allowable bending stress of the wood is 860 psi. Determine the magnitude of the maximum load w that may be carried by the beam. b Answer: w = i lb/ft.