A simply supported wood beam of length L = 8 ft carries a concentrated load P at midspan, as shown. The cross- sectional dimensions of the beam are b = 7 in. and h = 13 in. If the allowable shear strength of the wood is 130 psi, determine the maximum load P that may be applied at midspan. Neglect the effects of the beam's self-weight. 12 Answer: P = IN P B 1/12 C X lb N b h

A simply supported wood beam of length L = 8 ft carries a concentrated load P at midspan, as shown. The cross- sectional dimensions of the beam are b = 7 in. and h = 13 in. If the allowable shear strength of the wood is 130 psi, determine the maximum load P that may be applied at midspan. Neglect the effects of the beam's self-weight. 12 Answer: P = IN P B 1/12 C X lb N b h

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. Steel and aluminum plates are used to reinforced 150 x 300 mm timber beam. The three materials are fastened firmly as shown so that there will be no relative movement between them. Given the following material properties, determine the safe resisting moment of the beam in KN.M. Allowable bending stress, Fb Modulus of Elasticity, E Steel = 137MPa %3D Steel = 217MPa Aluminum = 97 MPa Aluminum = 87 MPa %3! !3! Wood = 27 MPa Wood = 22 MPa 50mm CTEEL 150mm 300mm WeOD A LUAINUm 60mm
Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including its own weight) and a live load moment of 300kN.m. The beam is limited in size to 350mm by 600mm overall depth. Steel covering from centroid of bars to outermost fiber is 100mm for both tension and compression reinforcement. Use fc'=27.5Mpa, fy = 414MPa,20mm barsA. As'= 7 of 20mm and As=14 of 20mmB. As' = 9 of 20mm and As=18 of 20mmC. As'= 5 of 20mm and As=10 of 20mmD. As' = 3 of 20mm and As=6 of 20mm Please provide neat and clear solutions Note: kindly check below answer
A rectangular beam which is limited to 350 mm by 650 mm is reinforced at the compression side with As’ = 1,000 mm2and on the tension side As = 4,000 mm2. The beam has an effective depth of 510 mm and its neutral axis is located at 127.84 mm below the top of the beam. Assume steel in tension yields but that in compression does not yield. F’c = 35 MPa, β = 0.81, fy = 400 MPa. Steel covering on top is 50 mm. Determine stress of steel in compression. Determine the depth of compression stress block. Determine the moment capacity of the beam.
A TIMBER BLOCK "B x B" mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A "B" mm AND 't' mm THICK STEEL PLATES. DETERMINE THE THICKNESS 't' SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY. B t B t PROB 04
Topic: Restrained Beams 140KN 2.5m 3.5m 5KN/m 3.2m МА 6m MB 11WL2 Pab² 5WL2 Pa?b MA = - MB = - 192 L2 192 L2 INSTRUCTION: 1. Determine the maximum stress in the timber beam with the size of 120 x 370mm.
show complete solutions and answer should be in 4 decimal places
The composite bar in the figure is firmly attached to unyielding supports. Compute the stress steel (psi) caused by the application of the axial load P = 59 kips L1 = 16in; L2 = 10in
S9. Knowing that the allowable normal stress for the steel used is 150 MPa, select the most economical metric wide-flange beam to support the loading shown in Figure 9.0. 50 kN/m A D B -2.4 m- 0.8 m 0.8 m Figure 9.0 $10. Determine the average shearing stress in the web of the beam indicated and check whether the design obtained earlier for that beam is acceptable, knowing that the allowable shearing stress for the steel used is 110 MPa. Consider the beam of $9 above.
Note: Read the question carefully and give me both right solutions with clear calculations. Don't copy from already available solutions.
Question 4 A 6 KN force is applied at the free end of a wood (E = 12GPa) beam with dimensions given in Fig. Q4. Neglecting the effect of fillets and stress concentration, determine (a) the maximum compressive stress and its location at section A-A; (b) the maximum shearing stress and its location at section A-A; (c) the deflection at section A-A. 6 kN 300 mm 400 mm ΤΑ 叶 ¡A Fig. Q4 96 mm -- 12 mm 12 mm 48 mm
The two pieces of wood, 2 in. by 4 in., are glued together along the 40o joint. Determine the maximum safe axial load P that can be applied if the shear stress in the glue is limited to 250 psi