A simply supported wood beam of length L = 10 ft carries a concentrated load P at midspan, as shown. The cross-sectional dimensions of the beam are b=4 in. and h = 7 in. If the allowable shear strength of the wood is 100 psi, determine the maximum load P that may be applied at midspan. Neglect the effects of the beam's self-weight. Answer: P = i باد B lb b

A simply supported wood beam of length L = 10 ft carries a concentrated load P at midspan, as shown. The cross-sectional dimensions of the beam are b=4 in. and h = 7 in. If the allowable shear strength of the wood is 100 psi, determine the maximum load P that may be applied at midspan. Neglect the effects of the beam's self-weight. Answer: P = i باد B lb b

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please answer fast ASAP
A TIMBER BLOCK "B x B" mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A "B" mm AND 't' mm THICK STEEL PLATES. DETERMINE THE THICKNESS 't' SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY. B t B t PROB 04
The joist AB used in housing construction is to be made from 8-in. by 1.5-in. Southern-pine boards. The design loading on each board is placed as shown in the figure below. The allowable bending stress for the wood is Jallow 1.5 and the allowable shear stress is Tallow = 180 psi. Assume that the beam is simply supported from the walls at A and B. (Figure 1) Figure 1 ▾of 1 8 in. 150 lb L 150 lb L 150 lb L 1.5 in. Determine the largest room width I that the boards can span. Express your answer to three significant figures and include the appropriate units. L = 32.0 Submit μA ft My Answers Give Up ? Incorrect; Try Again; 3 attempts remaining
4. Find the maximum allowable value of P for the column. The cross- sectional areas and working stresses () are shown in Figure 3. 2P FIGURE 3 Steel: A=500 mm² Qw=120 MPa Timber: A=2000 mm² Ωw =12 MPa Timber: A=8000 mm² Ωw =16 MPa
show complete solutions and answer should be in 4 decimal places
A TIMBER BLOCK “B x B” mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A “B” mm AND ‘t’ mm THICK STEEL PLATES. DETERMINE THE THICKNESS ‘t’ SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY.
Design a reinforcement of a doubly reinforced beam if the beam has a size of 425 mm x 600 mm. Use fc = 21MPa , fy = 414MPa
A timber beam 150 mm wide and 200 mm deep is to be reinforced by bolting on two flitched each 150 mm x 12.5 mm in section. Find the moment of resistance when the flitched are attached symmetrically at the top and bottom. Allowable stress in timber is 6 N/mm². (Es= 20 Ew)
A simply supported wood beam of length L = 8 ft carries a concentrated load P at midspan, as shown. The cross- sectional dimensions of the beam are b = 7 in. and h = 13 in. If the allowable shear strength of the wood is 130 psi, determine the maximum load P that may be applied at midspan. Neglect the effects of the beam's self-weight. 12 Answer: P = IM P B 7/2 C X lb N b h