A built up section shown consists of A992 steel made from plates fully welded together. The flanges consist of PL16×380 and PL12×500 for the web. Fy = 345 mPa. Which of the following best gives the value of the section modulus? PL16X380 O 935x10^6 mm^4 O 3,514x10^3 mm^3 550x10^3 mm^3 O 3,887x10^3 mm^3 PL12x500

A built up section shown consists of A992 steel made from plates fully welded together. The flanges consist of PL16×380 and PL12×500 for the web. Fy = 345 mPa. Which of the following best gives the value of the section modulus? PL16X380 O 935x10^6 mm^4 O 3,514x10^3 mm^3 550x10^3 mm^3 O 3,887x10^3 mm^3 PL12x500

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 76 mm x 76 mm x 6 mm angular section is welded to a gusset plate having a thickness of 10 mm as shown in the figure. The length L1 equals 125 mm and L2 is 65 mm. The angular section has a cross sectional area of 929 mm2, Fy = 248 MPa, FU = 400 MPa. a. Determine the value of the tensile force P based on gross area in kN. b. Determine the value of tensile force P (KN) based on net area if the value of shear lag factor is 0.85. c. Determine the value of tensile force P based on block shear in gusset plate along the weld in kN. gusset plate L₂= 65 mm 25 m Allowable stresses: Allowable tensile stress (gross area) = 0.6Fy Allowable tensile stress (net area) = 0.50Fu Allowable shear stress (net area) = 0.30Fu P
Figure shows a beam made from bronze subjected to a 3.5 kN.m bending couple and its respective tensile properties. 1) Determine radius of curvature for the beam, ρ
Q2/ Find (x) so that the rigid beam remains in a horizontal position. Aluminum L = 5m A = 400mm² E = 70GPA Steel L = 3m A = 500mm? E = 200GPA 5m %3D Rigid beam Answer: x = 0.719m P = 50kN
To reinforce a column in an existing structure, two channels are welded to the W 12 x 50 column section as shown in the figure. Effective length of column with respect to each axis is 4.8 m. Kx = Ky = 1.0 Properties of W12 x 50 A = 9484 mm2 rx = 131.57 mm ry = 49.78 mm Ix = 164 x 106 mm4 Iy = 23 x 106 mm4 Fy = 345 MPa d = 309.63 mm Properties of C6 x 13 A = 2471 mm2 Ix = 7.24 x 106 mm4 Iy = 0.44 x 106 mm4 bf = 54.79 mm x = 13.06 mm (centroid from the outer side of the web) a. Determine the critical slenderness ratio. b. Determine the design strength of the column section. (kN in LRFD)
Please answer correctly and box the final answer
Need help with those asked in red within the text pleaseee
Please show solutions on how to get the x bar only. The circle green in the figure. Civil engineering- steel design
A beam is of a cross- section in the form of a channel as shown in the figure STR - 2. When subjected to sagging bending moment about X-X axis, the ratio of maximum compressive stress to tensile stress is 7:3. Determine the dimension b. I need answer ASAP. Thank you!
Problem 4.8 The truss is made of three A-36 steel members, each having a cross-sectional area of 400 mm². Part A Determine the magnitude P required to displace the roller to the right 0.28 mm. Express your answer to three significant figures and include appropriate units. Di Submit μA P = 0.09224 mm Previous Answers Request Answer ? 0.8 m 0.8 m - 5 kN 0.6 m-
Determine the type and amount of stress in each member of the truss shown below due to wind load using the method of joints. Assume RaH = RbH a.) Solve the stress of all the members b.) Tabulate your answers (length, bar force, type of force)
Need ASAP
The rigid bar AB, attached to two vertical rods as shown in the figure, is horizontal before the load is applied. If the load P = 50 kN, determine its vertical movement. STEEL L=3 M A= 300 mm² E= 200 GPa 2m зм P= 50 KN ALUMINUM L=43 A== 1500 mm² E-7067.