The cross section shown in the figure is a structural member known as a z-section. Yo 3/4 6-4.5 3/4 3.5 ********** ******* 2.625 -3/4 1.375 3.5 -Xo 3/4

Q: How do you convert gpm to ft?

A: A cross-sectional area's flow of fluid is measured in gallons per minute. In simple terms, it…

Q: Whose responsibility is it to create the as-built BIM? Architect / Engineer to complete designers'…

A: This question is related to the Building design from Civil Engineering.

Q: The Vicatronic

A:

Q: What are some common sources of groundwater pollutants?

A: This problem is related to Water pollution from Environment Engineering. In this question ask about…

Q: Define Gas sampling.

A: Gas sampling is a method by which the chemical, thermal, and hydrological properties of a surface or…

Q: advertised Distance & Reported Distance?

A: To find : Advertised distance and reported distance.

Q: How does USGBC operate?

A: - USGBC is acronym for United States Green Building Council. - USGBC is formed to provide new…

Q: Draw the complete shearing force diagram and bending moment diagram for the beam shown below. State…

A: A beam is simply supported at two ends. Two UDLs of 500 N/m at each end 0.3 m from the supports A…

Q: What is PD 1594. Explain

A: Introduction:- PD 1594 (PRESIDENTIAL DECREE No. 1594) Prescribing polices, Guidelines, Rules and…

Q: A composite assembly consisting of a steel (G = 80 GPa] core (2) connected by rigid plates at the…

A:

Q: Difference between fire resistance rating and spread fire rating

A: The fire resistance rating of a material typically refers to the time a construction material can…

Q: Define Building Perimeter Firestopping.

A: The prevention of fire through building is known as firestopping.

Q: Distinguish between intermittent system and continuous system of water supply

A: In Intermittent system water supply is divided into several zone and each zone is supplied with…

Q: Q2) From figure below compute:- a) CBA area. b) Level difference between A and B. staff in A staff…

A:

Q: The parents want to subdivide their inner lot into two equal area for their two sons such that the…

A:

Q: How is the inspection plan developed?

A: - Inspection plan is developed to provide information on the testing characteristics to ensure the…

Q: Describe Source Correction Method.

A: Solution: The source correction method is the effective method that is used as effective methods to…

Q: What is the 60 minute maximum rainfall intensity in in/hr? Refer to the Table below to answer the…

A:

Q: Define Full form of "CASBEE"

A: CASBEE is a tool for assessing and ranking building and design and environmental efficiency. It is a…

Q: RITING ITLED d. What is the difference in elevation between TP15 and TP30? (Ans.) e. What is the…

A:

Q: Briefly describe the CSI Specifications?

A: CSI stands for the Construction Specification Institute. CSI has introduced a common format for…

Q: BEAUTIFUL 01/ Construct Polynomial Forth function gases in cas, within [0, 1]ns4

A:

Q: A 3% ascending grade meets a descending grade at the vertex at station 2+050 and elevation 100m with…

A:

Q: Define SLS requirement

A: Solution: A Service level specification basically forms a part of the service level agreement in…

Q: 05: Explain the following terms (Paste pictures to explain the following Signs):​(CLO 3) i.…

A:

Q: Write the disadvantages caused if any inspector fails to keep adequaterecords?

A: The person who is responsible for all the monitoring and assurity of completion of work with the…

Q: Civil Engineering [x – 5xgxf + 4x} *CX³NT = 20 4x - 5x,x2 + x}] Muestre que: * Xk-Xj 20 |

A: For 1 D, 2 node element the shape function is given as:…

Q: Road construction specifications

A: The asphalt is in road construction, wherever it is used as the glue or binder mixed with…

Q: Q1:A plate (0.005 cm )distance from a fixed plate move at (72000 mm/min) and requires a force of…

A:

Q: Compute for the latitude of Line 1-2 A +4.81 B) +5.79 +8.03 D -18.63 Question 11 Compute for the…

A: Data is as given

Q: Vill pela fomonte Batama VELIKATEe min htt Spring 500 # 750 T PERNI # 250" VERKS Draw V&M diagrams…

A: Given:Required:Shear and moment diagram

Q: What is filter drag model?

A: Answer:- Filter Drag Model:- The resistance across the fabric dust layer is called filter drag. The…

Q: Describe seepage velocity.

A: Seepage velocity seems to be the groundwater velocity determined according to the Darcy rule.…

Q: Define the term Underabsorption of Over-Head?

A: Let’s first understand the definition of overhead: Overhead refers to the continuing business…

Q: Wht is design requirements

A: Whatever requirements that somehow a designer should usually have to follow while establishing the…

Q: i…

A:

Q: Describe how you would ensure a fire belt of appropriate width is created around the entire farm…

A: Solution: GIS  refers to the Geographic Information System which analyzes, manage, creates and maps…

Q: wing that is related to transportation engi

A: A working sketch or blueprint is one that is based on explanations. It's finished with a detailed…

Q: Define hydrogeology.

A: Hydrogeology:

Q: :Signs: Classification 1. Regulatory signs O 2. Warning signs O 3. Guide signs Studs (Cat eyes)…

A: Sign classification on road and highway are :

Q: sdadsa

A: sdadsa

Site Plan Requirements

A site plan (also known as a plot plan) is a diagram or process to show the proposed improvements on an existing property. A site plan is important, as it provides information regarding the landscape features of a given plot of land.  Zoning is done or can be understood with the help of a site plan.