A 5-m diameter open cylindrical tank 10 m high contains sea water. It is made of steel 18 mm. thick. a. Determine the maximum circumferential stress when it is full of water. b. Determine the longitudinal stress near the bottom when it is full of water. c. Determine the depth of water will make the circumferential stress 10 MPa. d. Determine the required spacing of hoops if the pipe is bounded by 20 mm diameter steel hoops having an allowable stress of 99 MPa.

A 5-m diameter open cylindrical tank 10 m high contains sea water. It is made of steel 18 mm. thick. a. Determine the maximum circumferential stress when it is full of water. b. Determine the longitudinal stress near the bottom when it is full of water. c. Determine the depth of water will make the circumferential stress 10 MPa. d. Determine the required spacing of hoops if the pipe is bounded by 20 mm diameter steel hoops having an allowable stress of 99 MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Kindly answer. Thank you!
SECTION: 300 mm 10 KN m 800 mm A B 15m P= 300 KN e= 250 mm A. Calculate the stress at the top located in the centerline of the beam. (MPa) Calculate the stress at the bottom located in the centerline of the beam. (MPa) В.
Give me right solution according to the question
8. A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 15 in. and its length is 6.6 ft. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.
SHOW THE FBD AND DETAILED SOLUTION
The diameter of the shaft, shown below, is 60 mm and it is made of A-36 steel (E = 200 GPa and G = 75 GPa). The shaft is fixed at its ends A and B and is subjected to the loadings shown. Determine the absolute maximum torsional shear stress in the shaft. 500 N-m 200 N-m 1.5 m
HWAA traingular beam Beomm wide by 30omm height is Pinned at A, suPPorted by a cable CD and Carries a load (P) as shown in figure, Determine the max Valne of (P) that will not exceed a ombined normal stress of 120 Mla? Ans/ Prat - loo.3 W HoW:B Find the max Valne of (P) that canbe aPPlied on the Cantilever beam Shown in figure , knowing that the max Combined stresses will not exceed(22.67 MPa)in tension and (17.33 MPa) in cemPression? Ans/ Pmax 3D25W 450mm to Cable 30omm 150mm 50mm 300mm 2m Fig. (A) fig. (B)
The crane hook carries a load of 24 kN and the section at P-Q is rectangular as shown in the figure. Then find the total stress at the points P and Q. (Note: all dimensions in mm) P 1150 -100- 50 Section at P-Q 24 kN All dimensions in mm.
ka & pat 5em 2cm 4cm por Find steess the maximum chear and home Fined manent of inertia, T Find the normal stress/Volume and the Shear stress /volume as this volume is. directionally proportional to the mass of the beam. - Find in terms of P, and use MPA/mm³ for units.
a.) In ksi b.) In rad
7. A water tank 12 14 is completely filled with water. Determine the minimum thickness of the plate if stress is limited to 60 Mpa.
Required information The line of action of the 75-kip axial load Pis parallel to the geometric axis of the column AB and intersects the x axis at x = 0.6 in. Use E= 29 x 106 psi. W8 x 35 0.6 in.. B 20 ft Determine the maximum stress in the column. (Round the final answer to two decimal places.) The maximum stress in the column is 10 ksi.