The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A is closed and the water pressure is 300 psi, determine the longitudinal and hoop stress developed in the wall of the pipe. Draw the state of stress on a volume element located on the wall and its corresponding Mohr's Circle.

Q: a) Transform the beam into one made entirely of steel. b) The steel channel is used to reinforce…

A: Given Data The maximum moment (M) = 1.2 KN-m Est = 200 GPa Ew = 12 GPa We are asked to evaluate the…

Q: by m thick and e midpoint deflection is 24 O GPa. Answer must be ir

A:

Q: A flat steel bar, 29 mm wide by 4 mm thick and 1.8 m long, is bent by couples applied at the ends so…

A: Given data in question  Cross section Length Deflection  Elasticity modulus  To find out  Maximum…

Q: The frame supports the distributed load shown. Draw the free body diagram and find the reaction…

A: Draw FBD:

Q: Each of the four vertical links has an 8 X 36-mm uniform rectan- gular cross section, and each of…

A:

Q: A flat steel bar, 30 mm wide by 1 mm thick and 1.7 m long, is bent by couples applied at the ends so…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

A:

Q: A rod is composed of copper and steel section rigidly bolted in the wall as shown in the figure. If…

A:

Q: PROBLEMS 237. The lower ends of the three bars in the figure are at the same level before the rigid…

A:

Q: A rectangular cantiliver wooden beam is applied by point load of 400in at free end  Determine cross…

A: Direct stress: Stresses that act normally in relation to the plane of the object are referred to as…

Q: A flat steel bar, 27 mm wide by 3 mm thick and 1.7 m long, is bent by couples applied at the ends so…

A:

Q: A flat steel bar, 28 mm wide by 2 mm thick and 1.7 m long, is bent by couples applied at the ends so…

A:

Q: PROBLEM 1.3 75 mm 12AN Two solid cylindrical rods AB and BC are welded together at B and loaded as…

A:

Q: Cylindrical rod is placed inside a fube of the same length - the ends of the rod and tube are…

A:

Q: As seen in the figure, ABC rod with end-A fixed support pipe section has an outer diameter of 30 mm…

A: Consider the free body diagram

Q: Problem 2 (for all students). Determine the state of stress, the principal stress and the max in-…

A: Calculating the moment of inertia: IP=π32504-404    The torque will be:T=6×300=1800 KN-mmThe bending…

Q: The plate of thickness, t 5 mm, is loaded with the following stress; oy = 100 MPa, o, = -60 MPa, E =…

A:

Q: A three part bar is connected to walls at D and C and loaded as shown. Middle section AB is solid…

A:

Q: A flat steel bar, 28 mm wide by 5 mm thick and 1.7 m long, is bent by couples applied at the ends so…

A:

Q: A flat steel bar, 28 mm wide by 2 mm thick and 1.7 m long, is bent by couples applied at the ends so…

A: To find maximum stress in bar

Q: Two bars are made of a material with the stress-strain diagram as shown. Find the cross-sectional…

A:

Q: 9-6. Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem…

A:

Q: A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its…

A: A steel pipe is subjected to the 16-kN load shown below.Outer diameter = 140 mmThickness = 7 mmYield…

Q: loaded as shown. Knowing that dị = 30 mm and d, = 50 mm, find the average normal stress at the…

A: To find the average normal stress in rod AB and BC -

Q: A flat steel bar, 26 mm wide by 2 mm thick and 1.8 m long, is bent by couples applied at the ends so…

A: Given, length of the bar =1.8m width = 26mm thickness =2mm mid deflection =27mm E= 220 Gpa   our aim…

Q: B) A steel rod with a cross sectional area of (12 mm 12 mm) is stretched between two fixed points.…

A:

Q: de by 2 mm hick and 1.3 m long, is bent by ouples applied at the ends so that he midpoint deflection…

A:

Q: A flat steel bar, 26 mm wide by 3 mm thick and 1.7 m long, is bent by couples applied at the ends so…

A: Calculate maximum stress in bar=?

Q: (a) Draw the stress element for point B at the top center of the bar (right end) and label the…

A: The values and diagrams given in the question are as follows: Length of the bar(L)=180 mm Depth of…

Q: 2. Calculate the increase in stress in each segment of the compound bar if the temperature is…

A: Given data in question  Area Elastic modulus  Coefficient of thermal expansion  Increase in…

Q: 6 - A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under…

A:

Q: A rectangular column section is as shown in the figure. 200 mm There is a load of 200 kN, acting on…

A:

Q: A steel column of hollow circular cross section is supported on a circular, steel base plate and a…

A: A column is a vertical structural element that is used to transfer load from top to bottom. It has…

Q: A steel rectangular block is subjected to a uniform stress of o = 150 MPa acting on all faces. The…

A:

Q: Adosed cylindrical tank containing a pressurized fluid has an inside diameter of 472 mm anda wall…

A:

Pressure and Stress