Cylindrical rod is placed inside a fube of the same length - the ends of the rod and tube are attached to a rigid support one side and A vigid plate on the other the load on the rod - tabe assembly is increased from zero to 26 KN and removed. Draw a load - deflection diagram & calculate the residual stresses in rod & tube Rod Tube Tube 2 mno A₁ =64.5 = 100 Gpa Rod ·P A₂ = 48.4mm² E =2006ра oy = oy - = 248 мра € Tube 1800 злом ра

Cylindrical rod is placed inside a fube of the same length - the ends of the rod and tube are attached to a rigid support one side and A vigid plate on the other the load on the rod - tabe assembly is increased from zero to 26 KN and removed. Draw a load - deflection diagram & calculate the residual stresses in rod & tube Rod Tube Tube 2 mno A₁ =64.5 = 100 Gpa Rod ·P A₂ = 48.4mm² E =2006ра oy = oy - = 248 мра € Tube 1800 злом ра

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

6 - A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under the applied torque, what is the maximum shear stress in each material? The composite shaft is attached to a wall at A. Im B OPT. →→→→T= 5 KN•m Steel core r=15mm G=78 GPa bross cylinder ro=20mm (outer diameter) G=39 GPa
2.31 The three symmetrically placed rods support the rigid block of mass M. Before the block was attached, the rods' ends were leveled. If the rods' properties are as listed, find the maximum allowable value of M. (sw is the working stress). ow. 1.2m 1.2m 260mm 180mm Copper
Mechanics of Deformable Bodies. Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d1 5 30 mm and d2 5 50 mm, find the average normal stress at the midsection of (a) rod AB, (b) rod BC.
222. two decimal places
135 mm 85 mm σ, = -58 MPa E = 105 GPa D = 0.33 Beer & Johnston & DeWolf & Mazurek 2.86 (a) For the axial loading shown, determine the change in height and the change in volume of the brass cylinder shown. (b) Solve part a, assuming that the loading is hydrostatic with Ox= Oy = O₂ = -70 MPa
A flat steel bar, 26 mm wide by 2 mm thick and 1.8 m long, is bent by couples applied at the ends so that the midpoint deflection is 27 mm. Compute the maximum stress in the bar. Use E =220 GPa. Answer must be in MPa.
A flat steel bar, 26 mm wide by 3 mm thick and 1.7 m long, is bent by couples applied at the ends so that the midpoint deflection is 21 mm. Compute the maximum stress in the bar. Use E = 240 GPa. Answer must be in MPa.
Three aluminum rods support the rigid L-shaped bracket BCF as shown in the figure. Determine the stress in rod DE (express answer in MPa) if rod FG is cooled by 50°C. All three rods have the same cross-sectional area of 1000 mm^2. Use 73.1 GPa and 23 x 10^-6/°C for the modulus of elasticity and the coefficient of thermal expansion of aluminum, respectively.
(a) 128.5 GPa circular rod of diameter 30 mm and length 200 mm is subjected to a tensile force. The axtension of rod is 0.09 mm and change in diameter is 0.0045 mm. What is the Poisson's ratio of the material of the rod? (a) 0.35 (b) 0.33 (c) 0.32 (d) 0.30
Determine the state of stress acting at point D. Take P₁ = 50 kN and P2 = 10 kN. OD= B ANSWER: P₁ TD= -1.5 m 1.5 m--1.5 m- 0.5 m 40 mm 100 mm 60 mm T D E P₂ 80 mm Part A Find o D. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. ANSWER: C Q Tap image to zoom Part B Find TD- Express your answer to three significant figures and include the appropriate units.
please just solve the second part
I will rate immediately, thank you!