C 1 ft 2 ft B 150 lb-ft/ft A 2 ft A copper pipe is tightly secured to the wall at C and a uniformly distributed torque is applied to it as shown, determine the shear stress at point A. The pipe has an outer diameter of 3.5 in and an inner diameter of 2 in. The point lies on the pipe's outer surface. Provide your answer in psi.

C 1 ft 2 ft B 150 lb-ft/ft A 2 ft A copper pipe is tightly secured to the wall at C and a uniformly distributed torque is applied to it as shown, determine the shear stress at point A. The pipe has an outer diameter of 3.5 in and an inner diameter of 2 in. The point lies on the pipe's outer surface. Provide your answer in psi.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A Single rivet lap joint is to commect 12 mm thick plates by providing 20mm dia. rivet at so mm pitch. determine the strength of the joint and joint efficiency. Take working stress. in shear in rivets = 80N/mm², working stress in beaning in rivets = 250 N/mm² and working stress in axial tension in plates = 150 N/mm².
Torialai Stan Problem 1-- Short link BD consists of a single steel bar 40 mm wide and 12 mm thick. Knowing that = Call 100 Mpa, determine: a) The maximum value of the normal stress in the link BD b) The required pin diameter at support D. 20kN 100 150 mm 300 mm D 30
Problem 1: Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T=2880 N and T;=432 N. The maximum bending moment is atx= 230 mm (point B), and it equals M= 698.3 N•m completely reversed, where the torque is constant at 612 N.m at the same point. The shaft material is AISI 1020 CD steel. Take the stress concentration conditions at B to be Shoulder fillet-sharp, with notch radius r=0.6 mm (Table 7-1). y 230 mm T, 280 mm 30-mm dia. T C 300 mm 250-mm dia. 400-mm dia. 270 N 1800 N a) Sketch a general shaft layout in 2D (x – y axes), including all components and torques, then calculate all reactions. b) Based on the current shaft dimensions and using only forces at B and C, find the lowest critical speed of the shaft. c) Discard the indicated shaft diameter and use DE-Goodman criteria to determine the critical diameter of the shaft based on infinite fatigue life with a design factor n of 1.5. (Take the same value of endurance limit as that used in…
Solve this question as soon as I upvote solution
Calculate the safe shear stress value of the shaft, given that the smallest allowable diameter d of the shaft subjected to forces P and Q is given as 60 mm in the figure?
SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Мра. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm F F mm. 50 mm 340 mm
A solid 2.20 in. diameter shaft is subjected to a torque of T = 365 lb-ft and an axial load of P = 4700 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = i Op2 i = Tmax in-plane A i H (1) psi psi psi T B (b) Show the stresses of part (a) and their directions on an appropriate sketch.
For the shown Fig., find the maximum shearing stress in bronze part of the shaft. * Steel d= 200mm G= 80GPa Bronze d= 100mm d= 100mm G= 40GPa G= 30GPA 2KN.m Aluminum 8KN.m 3kN.m 3m 2m 1.5m +
02: The rigid platform has negligible mass and rests on two steel bars, each 250.00 mm long. The center bar is aluminum and 249.90 mm long. Compute the stress in the aluminum bar after the center load P= 400 kN has been applied. For each steel bar, the area is 1200 mm2 and E= 200 GPa. For the aluminum bar, the area is 2400 mm2 and E 70 GPa Rigid platform Steel Ahmum Steel
A compound shaft made of steel and aluminium transmits 75 kW at 900 rpm. Determine the maximum shear stress and relative angle of twist between surfaces at two extreme ends located at A and C. Neglect any strain concentration effect. Esteel = 207 GPa, EA1 = 73 GPa, VAI = 0.334, and Vsteel = 0.33. F Aluminium 60 800- B Steel 75 1000 All dimensions are in mm
Adosed cylindrical tank containinga pressurized fluid has an inside diameter of 472 mm and a wall thickness of 10 mm. The tank is pressurized to 240 MPa. Determine the absolute maximum shear stress on the inner surface of the cylinder wall. 40.2 MPa O 295 MPa 35.0 MPa O 272 MPa O 20.9 MPa