A 1 mm thick cylindrical tube, 100 mm in diameter, is orthogonally turned such that the entire wall thickness of the tube is cut in a single pass. The axial feed of the tool is 1 m/minute and the specific cutting energy (u) of the tube material is 6 J/mm³. Neglect contribution of feed force towards power. The power required to carry out this operation is

A 1 mm thick cylindrical tube, 100 mm in diameter, is orthogonally turned such that the entire wall thickness of the tube is cut in a single pass. The axial feed of the tool is 1 m/minute and the specific cutting energy (u) of the tube material is 6 J/mm³. Neglect contribution of feed force towards power. The power required to carry out this operation is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q5/A/ 125 mm long, 10 mm diameter stainless steel rod is being reduced in diameter to 9 mm by turning on a lathe. The spindle rotates at N= 360 rpm, and the tool is traveling at an feed of 0.49 mm/rev. Calculate the cutting speed in units (m/s), MRR, and cutting time.
3. Draw the forces and angles involved in the cutting process and calculate shear angle (0), friction coefficient and tangential force if .cutting force 80 kN, resultant of forces 100KN, friction force-75KN, rake angle =20° undeformed chip thickness %3D 0.65mm and deformed chip thickness 0.72mm. %3D
a rod is to be manufactured using turning operations and is made of Nickel alloy. The rod is 80 mm in length and 15 mm in diameter. The final required diameter is 10 mm and the spindle rotates at N = 500 rpm while the tool axial speed is 100 mm/ min. Calculate material removal rate, cutting speed, cutting time, the power dissipated, and cutting force.
In a straight turning operations the diameter of a workpiece is reduced from 50 mm 40 mm using a feed rate of 0.1 mm/rev. The cutting tool used for the process has a normal working rake angle of 15°, clearance angle of 4° and a lead angle of 90°. The cutting force of 1200N and a thrust force of 660 N is measured during cutting operations. The workpiece material was stainless steel with a density of 7850 Kg/m³, thermal conductivity is 15 J/smK, specific heat is 480 J/kgK. The width of the secondary deformation zone divided by the chip thickness wo is assumed to be 0.2 for the above mentioned cutting conditions. The chip/tool contact length is measured as 1.5 mm. (a) Calculate the temperature rise in the primary deformation zone (b) Calculate the temperature rise in the secondary deformation zone (c) Calculate the maximum temperature if the room temperature is 24°C If the tool life for the average cutting velocity of 90 m/min is measured as 10 min. and for a cutting velocity of 160 m/min…
(b) A 400 mm long, 19.5 mm diameter of 304 stainless steel rod (assume specific energy of steel is 4 W.s/mm³) is being reduced in diameter to 17 mm by turning on a lathe machine. The spindle rotates at N = 700 rpm, and the tool is traveling at an axial speed of 300 mm/min. Calculate: (i) (ii) (iii) (iv) (v) cutting speed material removal rate cutting time power dissipated cutting force
A cylinder of 25 mm diameter and 100 mm length is turned with a tool, for which the relation VTO 25 = 55 is applicable. The cutting velocity is 22 m/min. For a tool feed of 0.046 mm/rev, the number of tool regrinds required to produce 425 cylinders is (a) 12 (c) 43 %3D (b) 22 (d) 85
Problem 10.21 Estimate the time required for one complete cut on a workpiece of length 350 mm and diameter 70 mm by a cutting tool which operates at 35 m/min. Take feed to be 0.25 mm/rev.
An orthogonal cutting operation is being carried out under the following conditions: depth of cut, to = 0.1 mm, rake angle, a = 10°, Cutting force, Fc =1500 N, and Thrust force, Ft = 800 N. Calculate the shear force.
An orthogonal cutting operations is being carried out in which uncut thickness is 0.010 mm, cutting speed is 130 m/min, rake angle is 15° and width of cut is 6 mm. It is observed that the chip thickness is 0.015 mm, the cutting force is 60 N and the thrust force is 25 N. The ratio of friction energy to total energy is (correct to two