Answered: A cylinder of 25 mm diameter and length…

A cylinder of 25 mm diameter and length is turned with a tool, for which the relation VTO 25 = 55 is applicable. The cutting velocity is 22 m/min. For a tool feed of 0.046 mm/rev, produce

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(10) The lead screw of a lathe has a 2.0-in Acme thread, 2%2TPI. To drive the tool carriage, this screw must exert an axial force of 600lb. The thrust is carried on the collar 4½-in outside diameter & 244- in in inside diameter. The lead screw revolves 30rpm. Determine: (a) the efficiency of the screw & the collar, assuming f = 0.15 & fc = 0.10; (b) the power to drive the screw.
A steel shaft of 75 mm diameter and 250 mm long turned on a lathe. Speed of spindle = 2 m/s, feed = 0.25 mm/rev. Find time required for 50 jobs by assuming 2 minutes for handling of each job.
Q5/A/ 125 mm long, 10 mm diameter stainless steel rod is being reduced in diameter to 9 mm by turning on a lathe. The spindle rotates at N= 360 rpm, and the tool is traveling at an feed of 0.49 mm/rev. Calculate the cutting speed in units (m/s), MRR, and cutting time.
A 200 mm long magnesium alloy bar, 63 mm in diameter is turned on a lathe using a high speed steel cutter travelling at 180 mm/min. The spindle rotates at 450 rpm and lathe is equipped with a 10 kW motor, operating at a mechanical efficiency of 92%. The final diameter of the magnesium alloy bar is 59,5 mm. Indicate with a sketch the recommend size and location of the following tool angles: back rake, side rake, end relief, side relief and side and end cutting edge. Calculate the cutting time for the machining process.Calculate the required cutting force.
A mild steel block of width 40 mm is being milled using a straight slab cutter 70 mm diameter with 30 teeth. If the cutter rotates at 40 rpm, and depth of cut is 2 mm, what is the value of maximum uncut chip thickness when the table feed is 20 mm/min?
In a straight turning operations the diameter of a workpiece is reduced from 50 mm 40 mm using a feed rate of 0.1 mm/rev. The cutting tool used for the process has a normal working rake angle of 15°, clearance angle of 4° and a lead angle of 90°. The cutting force of 1200N and a thrust force of 660 N is measured during cutting operations. The workpiece material was stainless steel with a density of 7850 Kg/m³, thermal conductivity is 15 J/smK, specific heat is 480 J/kgK. The width of the secondary deformation zone divided by the chip thickness wo is assumed to be 0.2 for the above mentioned cutting conditions. The chip/tool contact length is measured as 1.5 mm. (a) Calculate the temperature rise in the primary deformation zone (b) Calculate the temperature rise in the secondary deformation zone (c) Calculate the maximum temperature if the room temperature is 24°C If the tool life for the average cutting velocity of 90 m/min is measured as 10 min. and for a cutting velocity of 160 m/min…
A student is performing a turning operation with a workpiece with an initial diameter of 40 mm to produce a 30 mm diameter rod that is 100 mm long. The lathe power is 20 kW and is operating on 85% mechanical efficiency. If the student set the cutting speed to 0.5 m/min and the cutting tool is set to have a rake angle of 5 degrees: a.) What material can we choose for the rod is the coefficient of friction is 0.5? b.) If we select 4130 normalized heat-treated steel for the rod, and coefficient of friction is 0.5, what will the maximum depth of cut we can achieve?
6
In a turning operation, the workpiece diameter is Dm=44.00 mm and the diameter after the operation should be 22.00 mm. The cutting speed is set to 105.00 m/min and the federate is 0.03 mm/rev. Calculate the material 3 removal rate (Cm²Imin) for this operation (Do not input units). Your Answer: Answer
In turning of stales steel alloy, 1100 mm length and 400 mm diameter, the Feed was 0.35 mm/rev, and depth of cut = 2.5 mm. The tool used in this cutting is cemented carbide tool where Taylor tool life parameters are n = 0.24 and C = 450 (tool life (min) and cutting speed (m/min). Compute the cutting speed that will allow the tool life to be 10% longer than the machining time for this part.