A 125mm-diameter work-bar, 1200mm long is held between centers of an engine lathe. A 400mm portion of the length is to be turned down to 119mm diameter in one pass. The speed :of the spindle is 2.50 m/s, and the cutting time is 2.62min. Determine :the required depth of cut (i) Feed; and (ii) (iii) the metal removal rate

A 125mm-diameter work-bar, 1200mm long is held between centers of an engine lathe. A 400mm portion of the length is to be turned down to 119mm diameter in one pass. The speed :of the spindle is 2.50 m/s, and the cutting time is 2.62min. Determine :the required depth of cut (i) Feed; and (ii) (iii) the metal removal rate

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please Solve this problem
A turning operation is carried out on aluminum. Based on the specific energy values in the table in your text, determine material removal rate and cutting power in the operation under the following sets of conditions: (a) Cutting speed = 5.6 m/s, feed = 0.25 mm/rev, and depth of cut = 2.0 mm; and (b) cutting speed = 1.3 m/s, feed = 0.75 mm/rev, and depth of cut = 4.0 mm.
A slab-milling operation is being carried out on a block on a 200 mm-long, 150 mm-wide annealed mild steel block at a feed f=0.20mm/tooth and depth of cut d=2.5mm. The cutter is D=45 mm in dimater, has 20 straight teeth, rotates at N=110rpm and by the definition, is wider than the block to be machined. Calculate;1. Material removal2. Estimate the power and torque required for this operation3. Calculate the cutting time
A mild steel block of width 40 mm is being milled using a straight slab cutter 70 mm diameter with 30 teeth. If the cutter rotates at 40 rpm and depth of cut is 2 mm, determine the value of maximum uncut chip thickness when the table feed is 20 mm / min.
Using slot milling with a cutting tool surface width of 36mm was performed from the top surface to cut a workpiece of 85 x 42 x 8 cm into two equal parts. The milling cutter is 180 mm in diameter and has eight teeth. Cutting speed = 60 m/min, chip load = 0.35 mm/ tooth, and depth of cut = 2 mm, given that the setup and machine settings provide an approach distance of 7mm before actual cutting begins and an overtravel distance of 20 mm after actual cutting has finished, and the return time is a 4-second for idle pass stroke. Determine:- 1. What is the total machining time required for the entire workpiece? 2. The maximum metal removal rate during cutting.
We need to obtain the following part by OD operation in turning, starting from a 100mm diameter cylinder. The maximum allowable depth of cut is 3mm. It is required to make a finishing pass with d=1mm and a feed of 0.3mm/revolution. 150 mm 150 mm The machine has a total power of 10hp and 85% efficiency. The material has a specific energy 500 based on of 25 W/(cm³/min). It is recommended to make the operation at a constant rpm = calculations made for an average diameter. Determine the minimum required time to finish the part. Hint: calculate the maximum material removal rate then the cutting speed for each pass, then the feed rate for each pass and finally the time of cutting. 80 mm 100 mm
In a turning operation on low carbon steel with hardness = 135 HB, the cutting speed = 180 m/min, feed = 0.35 mm/rev, and depth of cut = 6.5 mm. The original work piece has 26 mm Diameter and 120 mm Length. How much power will the lathe draw in performing this operation if its mechanical efficiency = 90% and operator's efficiency = 82%? The specific energy is 3.8 J/mm³
Q5/A/ 125 mm long, 10 mm diameter stainless steel rod is being reduced in diameter to 9 mm by turning on a lathe. The spindle rotates at N= 360 rpm, and the tool is traveling at an feed of 0.49 mm/rev. Calculate the cutting speed in units (m/s), MRR, and cutting time.
A 200 mm long magnesium alloy bar, 63 mm in diameter is turned on a lathe using a high speed steel cutter travelling at 180 mm/min. The spindle rotates at 450 rpm and lathe is equipped with a 10 kW motor, operating at a mechanical efficiency of 92%. The final diameter of the magnesium alloy bar is 59,5 mm. Indicate with a sketch the recommend size and location of the following tool angles: back rake, side rake, end relief, side relief and side and end cutting edge. Calculate the cutting time for the machining process.Calculate the required cutting force.
1. Peripheral milling is performed on the top surface of a rectangular work part that is 350 mm long by 60 mm wide. The milling cutter is 75 mm in diameter and has five teeth. It overhangs the width of the part on both sides. Cutting speed 55 m/min, chip load 0.25 mm/tooth, and depth of cut 5 mm. Maximum material removal rate during the cut will be mm/s. (a) 1419, (b) 1429, (c) 1439, (d) 1449, (e) 1459
A student is performing a turning operation with a workpiece with an initial diameter of 40 mm to produce a 30 mm diameter rod that is 100 mm long. The lathe power is 20 kW and is operating on 85% mechanical efficiency. If the student set the cutting speed to 0.5 m/min and the cutting tool is set to have a rake angle of 5 degrees: a.) What material can we choose for the rod is the coefficient of friction is 0.5? b.) If we select 4130 normalized heat-treated steel for the rod, and coefficient of friction is 0.5, what will the maximum depth of cut we can achieve?
b) A mild steel having length of 350mm and diameter of 12.5 cm, is being reduced to diameter 9.5 cm, for the length of 22cm by turning on lathe, with a spindle speed of 250rpm. Assume feed (f) 2.5 mm/rev and 2 passes to complete the turning operation. Write the formula and calculate (i) Cutting speed (ii) Depth of cut.