Answered: What is the recommended feed for the…

Engineering

Mechanical Engineering

What is the recommended feed for the turning operation above?

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter5: Turning

Section5.3: Machining Operations On The Lathe

Problem 2RQ: A lathe cross slide uses a diameter-reading micrometer collar. If the cross slide is advanced by...

See similar textbooks

Related questions

Q: In an orthogonal cutting operation an 8 mm deep groove is to be turned on a 50 mm diameter steel…

Q: A cast iron component for motorcycle is to be tumed with machine settings of feed = 0.22 mm/rev, and…

A: Surface roughness is calculated. If you liked my solution, I would really appreciate a LIKE, please…

Q: A 16mm Solid carbide tool with two teeth is used to machine Aluminium using the cutting speed of…

Q: A 12" through hole is to be drilled in a 1 inch thick steel plate. A standard twist drill having a…

Q: If a fairing operation is executed at a rotational speed of 40.0 rev / min, the feed is 0.015 in /…

A: As the outer and inner diameter is not given so I am assuming it as D0 and Direspectivelya)…

Q: A 0.4-inch diameter bit is used in a vertical or vertical drill that operates at 300 rpm. If the…

Q: A part to be turned in an engine lathe must have a surface finish of 1.6 μm. The part is made of a…

A: Proper tool Nose radiusing improves machinability to some extent though. It increase the tool life…

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

A Ø1.0” piece of titanium needs to be turned on a lathe using a carbide cutting tool. The surface speed is 170 ft/min and the chip load is .015 in/rev.

What is the recommended feed for the turning operation above?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Defining data given

VIEW

Step 2: Calculation of Feed

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A Ø2.0" piece of alloy steel needs to be turned in a lathe using a carbide cutting tool. The surface speed is 425 ft/min and the chip load is .008 in/rev. What is the recommended feed for the turning operation above? O .008 in/rev O .008 in/min O 6.8 in/rev O 425 in/min O 6.8 in/min
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes
Q1. Calculate the time required to machine a workpiece 170 mm long, 60 mm diameter to 165 mm long 50 mm diameter. The workpiece rotates at 440 rpm, feed is 0.3 mm/rev and maximum depth of cut is 2 mm. Assume total approach and overtravel distance as 5 mm for turning operation. Answer Q2. A gray cast iron surface 280 wide and 540mm long may be machined either on a vertical milling machine, using a 100mm - diameter face mill having eight inserted HSS teeth, or on a horizontal milling machine using an HSS slab mill with eight teeth on a 200-mm. diameter. Which machine has the faster cutting time? The values of feed per tooth and cutting speed for both processes are 0.4mm/tooth and 80m/min, respectively. The depth of cut = 3.0 mm and assume A and O equal to 5. Answer
In a turning operation on low carbon steel with hardness = 135 HB, the cutting speed = 180 m/min, feed = 0.35 mm/rev, and depth of cut = 6.5 mm. The original work piece has 26 mm Diameter and 120 mm Length. How much power will the lathe draw in performing this operation if its mechanical efficiency = 90% and operator's efficiency = 82%? The specific energy is 3.8 J/mm³
formula and calculation
The end of a large tubular workpart is to be faced on a NC vertical boring mill. The part has an outside diameter of 38.0 in and an inside diameter of 24.0 in. If the facing operation is performed at a rotational speed of 40.0 rev/min, feed of 0.015 in/rev, and depth of cut of 0.180 in, determine (a) the cutting time to complete the facing operation and the cutting speeds and metal removal rates at the beginning and end of the cut.
(j) In a turning operation on stainless steel with hardness = 200 HB, the cutting speed = 250 m/min, feed = 0.3 mm/rev, and depth of cut = 8 mm. How much power will the lathe draw in performing this operation if its mechanical efficiency = 95%. Use Table below to obtain the appropriate specific energy value.
A turning operation is performed on C1008 steel (a ductile steel) using a tool with a nose radius = 1.3 mm. Cutting speed = 61 m/min and feed = 0.27 mm/rev. Compute an estimate of the surface roughness in this operation. (Hint: the ratio of actual to ideal roughness can be read on the figure below) Equations used R₁ = f² 32NR Ra = rai Ri Actual Theoretical Ratio= 2.4 2.2 2.0 1.8 1.4 1.2 1.0 0 Ductile metals Cast irons Free machining alloys 100 I 30.5 200 Cutting speed-ft/min I 61 300 91.5 Cutting speed - m/min T 400 I 122
In a turning operation on cast iron, the nose radius onthe tool = 1.5 mm, feed = 0.22 mm/rev, and speed = 1.8m/s. Compute an estimate of the surface roughness forthis cut.
A drilling operation is performed to create a through hole on a steel plate that is 20 mm thick. Cutting speed = 0.4 m/s, and feed = 0.20 mm/rev. The 18-mm-diameter twist drill has a point angle of 120°. Determine the following once the drill reaches full diameter: a. the machining time and, b. the metal removal rate Equation used Tm TD₂L fv
In turning of stales steel alloy, 1100 mm length and 400 mm diameter, the Feed was 0.35 mm/rev, and depth of cut = 2.5 mm. The tool used in this cutting is cemented carbide tool where Taylor tool life parameters are n = 0.24 and C = 450 (tool life (min) and cutting speed (m/min). Compute the cutting speed that will allow the tool life to be 10% longer than the machining time for this part.