A 40cm diameter workbar that is 80cm long is to be turned down to a diameter of 35cm on an engine lathe. Cutting conditions are the following: cutting speed = 90m/min, feed = 0.35mm/rev. Are required two rough operations. The bar will be held in a chuck and supported on the opposite end in a live centre. With this workholding setup, one end must be turned to diameter; then the bar must be reversed to turn the other end. Using an overhead crane available at the lathe, the time to reverse the bar is 3.0 minutes. Loading and unloading operations (at the beginning and at the end of the manufacturing process) take a total of 5 minutes. For each turning cut an allowance must be added to the cut length for approach and overtravel. The total allowance (approach plus overtravel) = 15mm. Determine the total cycle time to complete this turning operation

A 40cm diameter workbar that is 80cm long is to be turned down to a diameter of 35cm on an engine lathe. Cutting conditions are the following: cutting speed = 90m/min, feed = 0.35mm/rev. Are required two rough operations. The bar will be held in a chuck and supported on the opposite end in a live centre. With this workholding setup, one end must be turned to diameter; then the bar must be reversed to turn the other end. Using an overhead crane available at the lathe, the time to reverse the bar is 3.0 minutes. Loading and unloading operations (at the beginning and at the end of the manufacturing process) take a total of 5 minutes. For each turning cut an allowance must be added to the cut length for approach and overtravel. The total allowance (approach plus overtravel) = 15mm. Determine the total cycle time to complete this turning operation

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Distributed load, w0 = 4 N/mL = 3.4 m Find the following: Find the magnitude of the equivalent concentrated force (in N). Find the distance of the equivalent concentrated force from A (in m).
Can you show work in writing instead of written out steps?
After completing the ENGR 315 hands-on project Sparky decided to create a symbolic solution for the time it takes for water to drain from the bottle. Sparky will compare the times to a YouTube video of the hands-on project. Sparky’s bottle is 4 inches in diameter and contains three holes of equal size (not what was required by the hands-on experiment). The hole size of diameter (dhole) is in inches and the holes are L inches apart. There is Ltop inches was water above the top hole at the start of the experiment (as shown in the figure). Neglecting viscous effects (orifice coefficient) and considering the flow conditions to be quasi-steady (consistent with the hands-on experiment) create a symbolic solution for the time it takes for water to stop draining from the top hole. The density (ρ) and specific weight (γ) of the water are 1.94 slugs/ft3 and 62.4 lbf/ft3, respectively. The height of water above the first hole is h, which varies with time. The flow through each hole is the…
A piston with area 2cm2 is moved at a speed of 1.5cm/s. What is the velocity in m/s if the outlet is 15mm2?
Find a) the total force on gate AB in KN and b) the position of the center of pressure in m with respect to the bottom of the pond. Assume that the gate is 8 feet wide, that 1ft = 0.3048m, and that 1PSI = 6897.1 Pa
The pump delivers water from the lower to the upper reservoir at the rate of 2.0 ft. The head loss S between the suction pipe inlet and the pump is 6ft and that between the pump outlet and the upper reservoir IS 12ft. Both pipes 6 inches Schedule 40 steel pipe. Calculate a)The pressure at the pump inlet in Psi,b) The pressure at the pump outlet in Psi,c) The total head on the pump in ft, andd) The power delivered by the pump to the water in Hp
Joe takes his little brother Andy down the the playground for an afternoon out. Andy would like to ride the seesaw, but the difference in their sizes, Joe weights 160lbs and Andy weighs 641lbs, makes this difficult. Joe sees a solution from his engineering class and moves the fulcrum from the middle to a new place. The seesaw is 3.5m long. After Joe moved the fulcrum how long was the seesaw on Joe's side?
The rate of water supply to a hydraulic crane is 90 liters per minute at a steady pressure of 70 bars. Find the input power and the efficiency if the output is 7.5 kW. The power in watts is the product of water supply pressure in N/m sq. and volume flow in M' per second.
If the water hp of a pump is 50 hp, the efficiency of the pump is 75%, and the efficiency of the motor is 90%, how many kw-hrs are consumed in one month’s operation? how many brake hp-hrs are consumed in one month’s operation? Answer should be 39,787 and 53,333. I need solutions thanks!!!
i need the answer quickly
A hydraulic cylinder has a 275 mm diameter. How much oil pressure P (kPa) is required to produce 12500 N force at its piston?
|20 kN 15 kN/m A 2 m 4 m B.