In Tinyland, houses are less than a foot high! The rainfall is laminar! The drainpipe in the figure is only 2 mm in diameter. Part (A) - When the gutter is full, what is the rate of draining? Part (B) - The gutter is designed for a sudden rainstorm of up to 4 mm per hour. For this condition, what is the maximum roof area that can be drained successfully Part (C) What is Red? Neglect minor losses. HINT : 4mm PER HOUR ***

Q: Q - The Crank radius of a single Minder IC engine is 60mm and the diameter of the cylinder is somm.…

A:

Q: 2. A vertical rectangular plate is submerged half in oil (sp. gr. = 0.8) and half in water such that…

A: Soln:- SP. Gravity of cylinder = 0.8 Density of oil = 800 kg/m^3 (F H) oil = p × g× h × A…

Q: Find the surface tension in a soap bubble of 40 mm diameter when the inside pressure is 2.5 N/m²…

A: The soap bubble is similar to water bubble. The formula of water bubble is to be used in this…

Q: FROM THE ATTACHED SKETCH, THE GIVEN DATA ARE AS FOLLOWS: a. Reservoir tank=50,000 liters of water b.…

A:

Q: The Deligne Dam on the Cayley River is built so that the wall facing the water is shaper like the…

A:

Q: .Mercury makes an angle of 130° when in contact with clean glass. What distance will mercury depress…

A:

Q: Rectangular tank contains 3.0 kg of air. The length of the tank is 1.0 m and the width is 1.5 m. The…

A: Rectangular tank contains m = 3.0 kg of air.The length of the tank is L = 1.0 m and the width is b =…

Q: USE IMAGE BELOW! Solve for parts A through C and Label Them

A:

Q: A ship has portholes to provide light and ventilation to lower decks. When there are large waves on…

A:

Q: A tank in the shape of a half-cylinder lies on its side as shown in the picture below. The units…

A:

Q: find the sea pressure in psig at the dive depth

A: This law states the guage pressure increases with the depth in static water. We have converted…

Q: 2.25 A fire-fighting nozzle is attached to a 3-in. flexible hose in which the pressure is 100 psi.…

A: In this question, the pressure at the inlet of pipe is given and the diameters of the pipe at the…

Q: Problem 2: Compressed Gas Tanks II Consider a compressed gas tank weighing 106 lb, 4.0 ft long, and…

A:

Q: A differential mercury manometer is used to measure the pressure drop across an orifice meter as…

A: please refer handwritten solution

Q: In an undisturbed airstream, the pressure is 14.7 psi, the density is 0.002378 slugs per cubic…

A: The velocity of undisturbed airstream: V = 628.7545 ft/sec

Q: Properties: blood viscosity µ-3.5cP and density 1.06g/cc. 1mmHg =133.3 Pa. 1Pa= 10 dynes/cm² Assume…

A: Write the given data. μ=3.5 cP=3.5×10-3 Ns/m2ρ=1.06 g/cc=1060 kg/m3P1=100 mmHg=13330 Pav1=60…

Q: Duct Pressure Drop: Determine the pressure drop, in inches of H20, for 300 feet of 12" diameter duct…

A: As per the guidelines, I can solve only first question. For rest question, repost in a separate…

Q: Suppose three volumes and three times, where the volume is in units cm3 and the time is in units of…

A: Laminar flow The fluid flows in parallel layers without any disturbance. Reynolds number for laminar…

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.