In orthogonal turning of low carbon steel pipe with principal cutting edge angle of 90°, the mair cutting force is 1000 N and the feed force is 800 N. The shear angle is 25° and orthogonal rake angle is zero. Employing Merchant's theory, the ratio of friction force to normal force acting on the

In orthogonal turning of low carbon steel pipe with principal cutting edge angle of 90°, the mair cutting force is 1000 N and the feed force is 800 N. The shear angle is 25° and orthogonal rake angle is zero. Employing Merchant's theory, the ratio of friction force to normal force acting on the

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 125mm-diameter work-bar, 1200mm long is held between centers of an engine lathe. A 400mm portion of the length is to be turned down to 119mm diameter in one pass. The speed :of the spindle is 2.50 m/s, and the cutting time is 2.62min. Determine :the required depth of cut (i) Feed; and (ii) (iii) the metal removal rate
Note: Read the question carefully and give me right solutions according to the question. In orthogonal cutting of steel tube of 150 mm diameter and 2 mm thick, the cutting force was 130 kg and feed force was 35 kg for chip thickness of 0.3mm. The orthogonal cut was taken at 60 meter per minute with a feed of 0.14 mm/rev. If the back rack angle of the cutting tool was - 8 o (minus 8 degree), then calculate the shear strain and strain energy per unit volume.
Manufacturing
A mild steel block is being drilled with a drill of 10 mm diameters. Given Helix angle = 30° Feed = 0.2 mm/rev %3D Ts = 450 N/mm? Estimate the drilling torque and thrust using Lee and Shaffer's shear angle relation. Assume the coefficient of friction between the chip and the drill to be 0.75.
I need a solution within 15 minutes
Please Solve this problem
Please solve it on neat paper.
(e) Briefly describe types of chips that occur in metal cutting. (f) For orthogonal cutting, the tool rake angle =15°. The chip thickness before the cut is 0.30mm and the cut yields a deformed chip thickness = 0.65mm. Calculate the shear plane angle and shear strain.
A seamless tube 32 mm outside diameter is turned on a lathe. The spindle speed used is 100 rpm. Rake angle = 35°, depth of cut = 0.125 mm, chip compression ratio = 1.666, feed= 0.1mm/rev, coefficient of friction= 1.53, resultant cutting force= 215.5N. Using the orthogonal model to approximate turning, Calculate: (1) Velocity of chip relative to the tool and workpiece, (2) Forces acting on the chip and the tool during orthogonal cutting, (3) Stresses acting on the shear plane and power dissipated in the shear zone, (4) Specific energy.
We need to obtain the following part by OD operation in turning, starting from a 100mm diameter cylinder. The maximum allowable depth of cut is 3mm. It is required to make a finishing pass with d=1mm and a feed of 0.3mm/revolution. 150 mm 150 mm The machine has a total power of 10hp and 85% efficiency. The material has a specific energy 500 based on of 25 W/(cm³/min). It is recommended to make the operation at a constant rpm = calculations made for an average diameter. Determine the minimum required time to finish the part. Hint: calculate the maximum material removal rate then the cutting speed for each pass, then the feed rate for each pass and finally the time of cutting. 80 mm 100 mm
3. Draw the forces and angles involved in the cutting process and calculate shear angle (0), friction coefficient and tangential force if .cutting force 80 kN, resultant of forces 100KN, friction force-75KN, rake angle =20° undeformed chip thickness %3D 0.65mm and deformed chip thickness 0.72mm. %3D
A circular shape blank will be cut of 105 mm diameter from a strip of 3.3 mm with a clearance value of 0.25 mm. Take the shear strength as 400 MPa. Determine The appropriate punch diameter. Blanking force. Blanking force when the blade angle is 5.5