63.A timber pile of length 8m and diameter of 0.2m is driven with a 20 kN drop hammer, falling freely from a height of 1.5m. The total penetration of the pile in the last 5 blows is 40 mm. Use the engineering news record expression. Assume a factor of safety of 6 and empirical factor (allowing reducing in the theoretical set, due to energy losses) of 2.5 cm. The safe load carrying capacity of the pile

63.A timber pile of length 8m and diameter of 0.2m is driven with a 20 kN drop hammer, falling freely from a height of 1.5m. The total penetration of the pile in the last 5 blows is 40 mm. Use the engineering news record expression. Assume a factor of safety of 6 and empirical factor (allowing reducing in the theoretical set, due to energy losses) of 2.5 cm. The safe load carrying capacity of the pile

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The wooden pile shown in the figure has a diameter of 100 mm and is subjected to a load of P = 70 kN. Along the length of the pile and around its perimeter, soil supplies a constant frictional resistance of w = 4.99 kN/m. The length of the pile is L = 4.2 m and its elastic modulus is E = 8.7 GPa.Calculate(a) the force FB needed at the base of the pile for equilibrium.(b) the magnitude of the downward displacement at A relative to B.
A 16 in diameter, 75 ft long drilled displacement pile is made of grout with f'c = 5,000 lb/in2. A steel ratio of 0.04 is to be used in the upper 30 ft, and a steel ratio of 0.001 for the remainder of the pile. Compute the modulus of elasticity for the upper and lower portions of this pile.
A timber pile of length 8m and diameter of 0.2m is driven with a 20 kN drop hammer, falling freely from a height of 1.5m. The total penetration of the pile in the last 5 blows is 40 mm. Use the engineering news record expression. Assume a factor of safety of 6 and empirical factor (allowing reducing in the theoretical set, due to energy losses) of 2.5 cm. The safe load carrying capacity of the pile
A timber pile of length 8m and diameter of 0.2m is driven with a 20 KN drop hammer, falling freely from a height of 1.5 m. The total penetration of the pile in the last 5 blows is 40mm. Use the Engineering News Record expression. Assume a factor of safety of 6 and empirical factor Callowing reducing in the theoretical set, due to energy losses) of 2.5 cm. The safe Load carrying capacity of the pile (in KN, round off to 2 decimal places) is
A prestressed concrete pile, 487 mm in diameter, is to be driven in a clayey soil. The pile has a design capacity of 401 kN. Use FS = 2, unconfined compressive strength = 168 kPa. Compute the length (in m.) of the pile if the frictional constant is 0.8.
None
The wooden pile shown in the figure has a diameter of 95 mm and is subjected to a load of P = 80 kN. Along the length of the pile and around its perimeter, soil supplies a constant frictional resistance of w = 2.90 kN/m. The length of the pile is L = 5.6 m and its elastic modulus is E = 8.6 GPa.Calculate(a) the force FB needed at the base of the pile for equilibrium.(b) the magnitude of the downward displacement at A relative to B.
The wooden pile shown in the figure has a diameter of 105 mm and is subjected to a load of P = 70 kN. Along the length of the pile and around its perimeter, soil supplies a constant frictional resistance of w = 3.85 kN/m. The length of the pile is L = 4.0 m and its elastic modulus is E= 12.9 GPa. Calculate (a) the force Fg needed at the base of the pile for equilibrium. (b) the magnitude of the downward displacement at A relative to B. y L Answers: (a) FB = (b) UA= i i B FB KN mm
63.A timber pile of length 8m and diameter of 0.2m is driven with a 20 kN drop hammer, falling freely from a height of 1.5m. The total penetration of the pile in the last 5 blows is 40 mm. Use the engineering news record expression. Assume a factor of safety of 6 and empirical factor (allowing reducing in the theoretical set, due to energy losses) of 2.5 cm. The safe load carrying capacity of the pile
Please round to the nearest Hundredth (i.e., 0.01). No Comma! A square pile, 13 m long is driven into a homogeneous sand layer. The pile's width (diameter) is 0.5 m. The standard penetration resistance near the vicinity of the pile is 17. Calculate the allowable bearing force (Qa) of the pile. Use FS = 2 and Briaud & Tucker method. Hint: Qa = Qu / FS Qa = KN
ge 4 Please round to the nearest Hundredth (i.e., 0.01). No Comma! A square pile, 26 m long is driven into a homogeneous sand layer. The pile's width (diameter) is 0.2 m. The standard penetration resistance near the vicinity of the pile is 17. Calculate the allowable bearing force (Qa) of the pile. Use FS = 3 and Briaud & Tucker method. Hint: Qa= Qu/FS Qa = kN S D F G H J Finish attempt... K
Using Engineering News formula, the allowable Load (Q) of a wooden pile hammered with a drop hammer (W = 30 kN), having free fall (H) 1.5 m, penetration in last blow (S) 5 mm, using empirical constant (C) as 2,5 and factor of safety as 6, will be