A prestressed concrete pile, 496 mm in diameter, is to be driven in a clayey soil. The pile has a design capacity of 404 kN. Use FS = 2, unconfined compressive strength = 158 kPa. Compute the length (in m.) of the pile if the frictional constant is 0.8. Round off to two decimal places.

Q: interior column loads are 500 tons and pile groups are not to exceed eight, determine the cross-…

A:

Q: A hammer is used to drive a wooden pile. The hammer weight is 25 kN and its free falling height is…

A:

Q: Q4) For the pile-soil system shown in Fig. (4), estimate the required pile length to carry an…

A: Given Data:Load = 24kN.For dense sandγsat=21kN/m3ϕ=40°ks=1.5

Q: Design a precast concrete pile subjected to an uplift Ioad of 500 kN and A Moment of 50 kNm. Use M30…

A:

Q: A rectangular pile (0.67 x 0.5 m.) is driven in a clayey soil arrangement composed of two different…

A:

Q: a. The ultimate point load using Meyerhof's procedure. b. The ultimate frictional resistance Qs.…

A:

Q: A prestressed concrete pile, 482 mm in diameter, is to be driven in a clayey soil. The pile has a…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: A12-in. steel H-pile is driven 60 ft into clay soil as follows: From the ground surface to a depth…

A: The load bearing capacity of the pile is given by,

Q: 2. A 0.45 m diameter, 20 m long, precast concrete pile is driven into a sandy soil profile. The SPT…

A: ###DETERMINATION OF Ultimate bearing Capacity of Driven Pile into a Sandy Soil wih SPT value given…

Q: (a) Determine the allowable load-carrying capacity of the bored concrete pile for: embedded length =…

A:

Q: Write a Short note on Statical Analysis (Single Pile Capacity).

A: Static Analytic Method Of Single Pile Capacity

Q: A 0.5 x 0.5m square concrete pile is to be driven in a homogeneous clayey soil having undrained…

A: given- 0.5 m×0.5 m,Cu=50 kPa,g=18 kN/m3,design capacity=500 kN,α=0.75.FOS=2.

Q: 12.7 A driven closed-ended pile, circular in cross section, is shown in Figure P12.7. Calculate the…

A: student asked part a and  part c only .Hence we have to answer part and part c only

Q: A solid steel pile (E = 200 GPa) with uniform diameter of 100 mm is driven into a soil layer and…

A: The given data is as follows: E=200 GPaDiameter of pile=100 mmVertical force=40 kNFrictional…

Q: and thereafter, Cu 132, 32, where z is the depth Z IS each strata. Determine the ultimate capacity…

A:

Q: Q- A precast concrete pile is driven with a 50 kN hammer falling through a height of 1.0 m with an…

A: Given- Weight of hammer W=50 kN, Height h=1 m, Efficiency n=0.6, Set value S= 4mm, Compression c=6…

Q: Q-4: A precast concrete pile of size 50 cm x 50 cm is to be driven into clay strata whose unconfined…

A:

Q: → A reinforced cement concrete pile weighing 30 kN (including helmet and dolly) isuriven by a drop…

A:

Q: Q-A precast concrete pile is driven with a 50 kN hammer falling through a height of 1.0 m with an…

A:

Q: 21 A prestressed concrete pile, 425 mm in diameter, is to be driven in a clayey soil. The pile has…

A: Given: Diameter of pile =425mm Design capacity =428 KN  Unconfined compressive strength =177 Kpa.…

Q: Find the force F in the image below such that the deep pile foundation under the structure frame…

A: Find Force F

Q: A prestressed concrete pile, 475 mm in diameter, is to be driven in a clayey soil. The pile has a…

A: NOTE :- Since, it is not given the type of pile so taking it as both end bearing and friction pile.…

Q: A drop hammer is used to drive a wooden pile. The hammer weight is 30 kN and its free falling height…

A: Given data,For drop hammer is used to drive a wooden pileWeight of hammer=30 kNFalling height =0.9…

Q: P-2 A 21.4-m-long HP 360*174 steel pile is 20m-embedded in a clay deposit and 1.4m above ground (…

A:

Q: P-2 A 21.4-m-long HP 360*174 steel pile is 20m-embedded in a clay deposit and 1.4m above ground (…

A:

Q: A 50 cm square prestressed concrete pile will be driven 20 m into the soil profile below. (water…

A: Given: A_b = (50 cm)2 / (100 cm/m)2 * pi / 4 = 0.196 m2 c' = 4 kPa (using ϕ= 28 deg) N_c = 14.7 N_q…

Q: A solid circular concrete pile is to be driven into a clayey soil with the following properties:…

A: Cu1 = 40 kPa Length (L1) = 5 m unit weight (γ1) = 15 kN/m3 Cu2 = 50 kPa Length (L2) = 10 m unit…

Q: o Given: A earth pile with L, E, and A known and constant F Y X (L-x) steel pile soil f =…

A:

Q: layey so friction factor of 0.81. Compute the allowable load that the pile can carry if the factor…

A:

Q: A prestressed concrete pile, 438 mm in diameter, is to be driven in a clayey soil. The pile has a…

A: To determine the length of the pile.   Given, Diameter of the pile, say D = 438 mm Design capacity…

Q: A 0.30-m square prestressed concrete pile is to be driven in a clayey soil as shown in figure. Use…

A: Given: size of pile  Cohesion  Aplha  To find: End bearing capacity Skin friction

Q: d. The ultimate frictional resistance Q₁. [Use Eqs. (12.42) through (12.44), and take K = 1.4 and 8'…

A: Given,Pile diameter (D) = 381 mm or 0.381 m Pile length (L) = 21 m

Q: A- The load (Q=900 ton) locate at x, determine the max. & min. pile reaction for the given condition…

A: The pile is the supporting or substructure for the bridge or building when loading is acting due to…

Q: A prestressed concrete pile, 409 mm in diameter, is to be driven in a clayey soil. The pile has a…

A: Hello dear this is the solution of your problem The answer is found to be Length of the pile in the…

Q: Estimate ultimate capacity of a timber pile with tip diameter of 180 mm and top diameter of 360 mm,…

A: Solution

Q: Figure below shows a precast circular pile is driven into two clay stratums to a depth of 14 m. the…

A:

Q: A prestressed concrete pile, 492 mm in diameter, is to be driven in a clayey soil. The pile has a…

A:

Q: Assuming a rigid pile, what is the minimum depth of penetration given a shear load of 894 lbs occurs…

A: Data Given: Shear force/Lateral Load = 894 lbse = 27 ftDiameter of the pile = 20 inches = 1.67 ftFOS…

Q: A rectangular pile (0.77 x 0.72 m) is driven in a clayey soil arrangement composed of two different…

A: Given  Pile dimensions : 0.77m x 0.72m Factor of safety : 2  Figure corresponds to given data: Skin…

Q: Design a bored pile carrying a <OMpressive load of 1000 kN ¤nd a moment of 50 kNm. Use M25 mix And…

A:

Q: A group of driven piles are to be built in layered soils as shown in the figure below. Please…

A: For ϕ = 35o ,   Nq = 33.5 Assuming pile to be concrete, and for loose sand {as γ=120psf}; k = 1…

Q: Calculate the pile's allowable bearing load using the corrected SPT values at various depths given…

A:

Q: Q Y- 17.5 kN/m Cohesion = 28 kPa a - 0.95 Y= 17.8 kN/m w = 25% & Gs = 2.6 Cohesion = 35 kPa a = 0.85…

A:

Q: 1. A1 ft x 1 ft size and 30 ft deep concrete pile is to be driven in the clay layer shown in the…

A: Size of footing  A=1×1=1 ft2depth of pile cap =3 ftthen length of footing 17 ft in soil A  and  30…

Q: Q3) For the pile-soil system shown in Fig. (3), estimate the required pile length to carry an…

A:

Braced cuts

The braced cut is a method of providing lateral support to the soil in foundation trenches, to prevent the trenches from deformation by the caving in of soil and resisting it from moving laterally. During shallow excavation in firm soil, generally, slopes are provided to resist the caving in of soil. During shallow excavation in soft soil and deep excavation, the chances of caving in of soil increase. Hence, it becomes necessary to make a provision to resist the deformation of trenches due to caving in of soil. The braced cut is the method used for such conditions. The excavation using braced cuts is a bit uneconomical as compared to the traditional open-cut excavation method but provides better safety than the cut excavation method.