P-2 A 21.4-m-long HP 360*174 steel pile is 20m-embedded in a clay deposit and 1.4m above ground ( e=1.4m). The pile is free-headed. Assume K= 9200 kN/m², the moment at ground level, Mg=0, and the allowable displacement of pile head =12 mm; Ep=207*106 kN/m²; and Fy = 248 MN/m?. Calculate the allowable lateral load, Qg, at the ground level if the soil is a Clay soil with C,=80 kPa . Use the Broms's method.

P-2 A 21.4-m-long HP 360174 steel pile is 20m-embedded in a clay deposit and 1.4m above ground ( e=1.4m). The pile is free-headed. Assume K= 9200 kN/m², the moment at ground level, Mg=0, and the allowable displacement of pile head =12 mm; Ep=207106 kN/m²; and Fy = 248 MN/m?. Calculate the allowable lateral load, Qg, at the ground level if the soil is a Clay soil with C,=80 kPa . Use the Broms's method.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following pile with a diameter of 600mm is driven into clay strata as provided below: Calculate the end bearing capacity if Nc = 8.5 Determine the skin friction capacity of the pile Find the allowable load if the factor of safety is 3.0 Please answer this asap. For upvote. Thank you
A concrete pile is 15 m long and has 406 mm diameter circular cross section. The pile is fully embedded in sand, for which the unit weight '( = 18 kN/m3 and the frictional angle 8 = 30°. i) Calculate the ultimate point load Qp ii) Determine the total frictional resistance Qs iii) Determine the total ultimate load ofthe pile.
A 40 cm diameter concrete pile, is driven to a depth of 15 m in a deep deposit of clay having unconfined compressive strength of 80 kN/m². The design load carrying capacity of pile will be [Assume α = 0.8 and FOS = 3] - (a) 648.42 kN (c) 432.28 KN ;) (b) 216.14 kN (d) 1296.84 kN
A prestressed concrete pile, 487 mm in diameter, is to be driven in a clayey soil. The pile has a design capacity of 401 kN. Use FS = 2, unconfined compressive strength = 168 kPa. Compute the length (in m.) of the pile if the frictional constant is 0.8.
63.A timber pile of length 8m and diameter of 0.2m is driven with a 20 kN drop hammer, falling freely from a height of 1.5m. The total penetration of the pile in the last 5 blows is 40 mm. Use the engineering news record expression. Assume a factor of safety of 6 and empirical factor (allowing reducing in the theoretical set, due to energy losses) of 2.5 cm. The safe load carrying capacity of the pile
Q1: Determine the allowable load capacity for the driven pile of 0.6 m diameter embedded in a layered soil as shown in the figure below, use F.S 2.0 , K, = 1.5 and tand =0.5? ELEV. 110 N.C.C W.T ELEV. 108 Cu =70 kPa Y = 17 kN/m3 a = 1, yw = 10 kN/m? ELEV. 102 O.C.C, Cu 180 kPa, y = 20 kN/m³ a = 0.45 ELEV. 98 Sandy Layer Yt = 19 kN/m3 Ø = 32° Nq = 23.18 ELEV. 90
ge 4 Please round to the nearest Hundredth (i.e., 0.01). No Comma! A square pile, 26 m long is driven into a homogeneous sand layer. The pile's width (diameter) is 0.2 m. The standard penetration resistance near the vicinity of the pile is 17. Calculate the allowable bearing force (Qa) of the pile. Use FS = 3 and Briaud & Tucker method. Hint: Qa= Qu/FS Qa = kN S D F G H J Finish attempt... K
subject
Please solve it in 30 minutes
i need the answer quickly
A circular pile is to be driven upto a depth of 10 m at a construction site. The average surface area of the pile is 2 m2 per meter length. The soil at the site is homogeneous sand, having effective friction angle of 30°. The ground water table (GWT) is at a depth of 4 m below the ground surface. The unit weights of the soil above and below the GWT are 18 kN/m3 and 20 kN/m3 respectively. Takek = 0.9 and the angle of wall friction (6) = 28°. The total axial frictional resistance mobilized on the pile against the driving is %3D kN. (Y = 9.81 kN/m³) %3D
A prestressed concrete pile, 484 mm in diameter, is to be driven in a clayey soil. The pile has a design capacity of 446 kN. Use FS = 2, unconfined compressive strength = 171 kPa. Compute the length (in m.) of the pile if the frictional constant is 0.8. Round off to two decimal places.