Figure below shows a precast circular pile is driven into two clay stratums to a depth of 14 m. the soil undrained shear strength properties are shown in the figure. Determine the size of the pile if the allowable load for this pile and the factor of safety is 99 kN and 2.5 respectively. (Take a as 1) 12 m 8 m Ground level Figuro at Om c= 30 kN/m² at 12m → cu = 30 kN/m² at 20mc₁ = 75 kN/m²

Figure below shows a precast circular pile is driven into two clay stratums to a depth of 14 m. the soil undrained shear strength properties are shown in the figure. Determine the size of the pile if the allowable load for this pile and the factor of safety is 99 kN and 2.5 respectively. (Take a as 1) 12 m 8 m Ground level Figuro at Om c= 30 kN/m² at 12m → cu = 30 kN/m² at 20mc₁ = 75 kN/m²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please solve under Geotechnology II.
A concrete pile, 350 mm square, is driven into a thick deposit of medium sand with φ= 35° and ϒ = 19kn/m3. The water table lies at 2.0 m below ground level. Estimate the length of pile required to support a working load of 450 KN assuming a an overall factor of safety of 2.5. I will report and downvote wrong answer
7. If a 45 cm diameter pipe pile is driven into clayey soil to a depth of 12 m. (a) what would the allowable load capacity (Q) be? The water table is 2 m below the ground surface and the soil profile consists of two clay layers (refer to the figure below). Use the ß method to calculate skin friction and the R=30° for all clay layers. (b) Explain how you selected FS value you use. 12 m ▶ 9m 2m 45 cm Y = 18.5kN/m³ = 30kN/m² Ysat = 19kN/m³ C₂ = 30kN/m² Ysat = 20kN/m² S = 60kN/m²
Please solve problem 3
A 20-m-long concrete pile is shown in Figure P9.1. Estimate the ultimate point load Q, by a. Meyerhof's method b. Vesic's method c. Coyle and Castello's method Use m = 600 in Eq. (9.26). 9.1 Concrete pile 460 mm x 460 mm Loose sand di = 30° y = 18.6 kN/m3 20 m Dense sand d'2 = 42° y = 18.5 kN/m3 Figure P9.1
Please find the question 1 is 2nd Image
The wooden pile shown in the figure has a diameter of 95 mm and is subjected to a load of P = 80 kN. Along the length of the pile and around its perimeter, soil supplies a constant frictional resistance of w = 2.90 kN/m. The length of the pile is L = 5.6 m and its elastic modulus is E = 8.6 GPa.Calculate(a) the force FB needed at the base of the pile for equilibrium.(b) the magnitude of the downward displacement at A relative to B.
The wooden pile shown in the figure has a diameter of 105 mm and is subjected to a load of P = 70 kN. Along the length of the pile and around its perimeter, soil supplies a constant frictional resistance of w = 3.85 kN/m. The length of the pile is L = 4.0 m and its elastic modulus is E= 12.9 GPa. Calculate (a) the force Fg needed at the base of the pile for equilibrium. (b) the magnitude of the downward displacement at A relative to B. y L Answers: (a) FB = (b) UA= i i B FB KN mm
Q1: Determine the allowable load capacity for the driven pile of 0.6 m diameter embedded in a layered soil as shown in the figure below, use F.S 2.0 , K, = 1.5 and tand =0.5? ELEV. 110 N.C.C W.T ELEV. 108 Cu =70 kPa Y = 17 kN/m3 a = 1, yw = 10 kN/m? ELEV. 102 O.C.C, Cu 180 kPa, y = 20 kN/m³ a = 0.45 ELEV. 98 Sandy Layer Yt = 19 kN/m3 Ø = 32° Nq = 23.18 ELEV. 90
The section of a 3 x 4 group pile in a layered saturated clay is shown in the figure below. The piles are square in cross section (356 mm x 356 mm). The center-to-center spacing, d, of the piles is 889 mm. Determine the allowable load-bearing capacity of the pile group. Use FS = 4. Note that the groundwater table coincides with the ground surface.
A rectangular pile (0.55 x 0.92 m.) is driven in a clayey soil arrangement composed of two different layers. First layer has a height of 6 m., cohesion of 54 kPa, friction factor of 0.83. Second layer has a height of 6 m., cohesion of 74 kPa, and friction factor of 0.8. Compute the allowable load that the pile can carry if the factor of safety is 2.52. Round off to two decimal places.