Calculate the pile's allowable bearing load using the corrected SPT values at various depths given in the figure below (factor of safety is 1.5). 10m D=1m 2m 2m 2m 2m 2m SPT1=14 SPT2=16 SPT3=18. SPT4=18. SPT5=20 Corrected SPT Values

Calculate the pile's allowable bearing load using the corrected SPT values at various depths given in the figure below (factor of safety is 1.5). 10m D=1m 2m 2m 2m 2m 2m SPT1=14 SPT2=16 SPT3=18. SPT4=18. SPT5=20 Corrected SPT Values

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter18: Pile Foundation

Section: Chapter Questions

Problem 18.14P: A steel pile (H-section; HP 360 1.491; see Table 18.1) is driven into a layer of sandstone The...

See similar textbooks

Related questions

Q: 6) A 2-ft x 2-ft square concrete pile is shown. Ignore the resistance of the soft clay. Assume Nq=…

A: B = 2 ft Nq = 10 FS = 3

Q: 2. Determine the allowable load carrying capacity of the pile shown below. The average unit skin…

A: Given that, average unit skin resistance = 1.2kN/m2 unit point resistance = 30kN/m2 FS=3.0 length…

Q: Estimate the pile length required to carry the 900 kN axial load for the pile-soil system shown the…

A: Given the details of Soil profile as:Soil 1:C= 35 kPaSoil 2:C= 45 kPaSoil 3:C= 55 kPaSoil 4:C= 60…

Q: Determine ultimate carrying capacity of pile of diameter 0.3m and length 10m driven into sandy soil…

A: Diameter of the pile = D = .3mLength of the pile = L = 10mUnit weight of soil = γ = 17KNm2ϕ = 30°

Q: A 12 inch diameter concrete pile is to be driven into a clay deposit as shown in Figure 2. The…

Q: A group of 25 HP 10 * 57 piles are arranged in a 5 * 5 grid at 27 inches on center and driven to a…

A: Given:- 5* 5 grid pile 25 HP 10*57 piles spacing , s = 27 inch s=2.25 feet L = 60 ft fn=1000 lb/ft2…

Q: Calculate the load bearing capacity of the pile shown in Figure Q5. Assume that it is a bored pile,…

A: Given, L = 18.5 m B = 0.60 m

Q: Q6) Determine the combined stress in HP 14 x 89 pile shown below. The pile is 25 feet long. E =…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement…

Q: Q3: What is the ultimate capacity of 4x4 concrete pile group shown in figure 3. The pile diameter…

A: Sheet piles are metal parts with interlocking edges driven into the ground to provide permanent or…

Q: A 14-in.-diameter steel pipe pile is driven 50 ft into overconsolidated clays having the following…

A: The ultimate bearing capacity of the pile is given by,

Q: 13) A cylindrical pile of diameter 0.3 m is driven to a depth of 15 m in to an NC clay as shown in…

A: Given; Diameter of pile (d) =0.3 m Depth of the pile (l) = 15 m Factor of safety (Fs) = 3

Q: Assume the curve shown in Figure 14.14 has been obtained from a static load test on a 60 ft long,…

Q: Check the total settlement of a group of pile as shown in Figure 1. The t

Q: Q-4: A precast concrete pile of size 50 cm x 50 cm is to be driven into clay strata whose unconfined…

Q: Design the anchored sheet pile wall supporting a loose sand fill as shown in the following Figure.…

Q: exampley Determine the ultimate load of closed ended pipe pile using the Static load test data of…

Q: X XXXX 4m 5m 6 m XX Key: PILE I Soil 1 c = 35 kPa Y = 16.79 kN/m³ Soil 2 GROUND LEVEL Soil 3 c = 45…

A: Soil profile:Soil 1:C= 35 kPaSoil 2:C= 45 kPaSoil 3:C= 55 kPaSoil 4:C= 60 kPa

Q: Compute the compressive force at the most stressed pile for each pile cap given in the table below.…

A: Weight of pile cap = 3.6*3.6*0.4*25 = 129.6 kN. = 3.6*3.0*0.4*25 =…

Q: al distance from the end shoul

A: solution of above problem is below:

Q: Describe about the pile impedance.

A: Pile impedance:

Q: A- The load (Q=900 ton) locate at x, determine the max. & min. pile reaction for the given condition…

A: The pile is the supporting or substructure for the bridge or building when loading is acting due to…

Q: QUESTION 3: Three forces act on a pile as shown. If the resultant of the three forces is equal to…

A: An arrangement of forces have been given and it has been asked to determine missing force and its…

Q: # 2. Discuss in your own words with the help of diagram, the load transfer mechanism in skin…

A: Given data in question Load transfer mechanism in piles with aid of diagram End bearing mechanism:…

Q: A 24 inch square prestressed concrete pile is to be driven to a depth of 68 ft into the following…

A: Square pile of size 24 in x 24 in Factor of safety is 3

Q: Discuss in your own words with the help of diagram, the load transfer mechanism in skin…

Q: 17) The friction load capacity of the pile using the B-method is most nearly: a. 437 kN b. 927 kN c.…

A: To determine- Friction load capacity

Q: Determine the allowable bearing load of the pile shown in figure Q1 using all the possible methods…

A: The soil is cohesive. We will only need cohesive soil parameters.

Q: Estimate the pile length required to carry the 670 kN axial load for the pile-soil system shown in…

A: Axial load, Pa = 670 kNPile diameter, D = 460 mmSafety factor = 3.0

Q: Determine load carrying capacity of pile without considering critical depth concept. Diameter of…

A: Answer We know that the load bearing capacity of pile(Q) is given by combination of point Bearing…

Q: 2. Two cylindrical steel piles (P1 and P2) are to be driven along the shore. Two total stations were…

A: The angle between TS1 and TS2 is, α=tan-13414.175-3021.8328415.591-6523.709α=11°42'57.82''…

Q: Situation. A 15m precast concrete pile is to be lifted. If the unit weight of concrete is 23.54kN/m3…

Q: Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement…

Q: Q=300KN W.T. D SAND Ysat (kN/m³) L=..(m) ...... p' = ...(") K = 1- sin(4) O = (2/3) p Figure Q2…

A: Data by putting value of i, j: L=5+8 = 13 m ϕ=30+0.5×8 = 34° D=0.55+0.05×7 = 0.9 m…

Q: square prestressed concrete pile with a 14 inch side is to be driven to the necessary depth. It…

A: Pile with a 14 inch side Qd = 2.5×105 = 262.5 kips qp =120 ksf fs = 450 psf fs =0.45 ksf Given…

Q: In which cases should the effect of negative frictional resistance on the pile side be considered?

A: #Negative skin friction (negative frictional resistance) :-Negative skin friction is downward drag…

Concept explainers

Pricing Excavation and Backfill

Backfill, in construction, is the activity of returning the soil and gravel that are removed during building construction or using them again to toughen and support the foundation of the building or any other structural component.

Question

Calculate the pile's allowable bearing load using the corrected SPT values at various
depths given in the figure below (factor of safety is 1.5).
10m
D=1m
2m
2m
2m
2m
2m
SPT1=14.
SPT2=16
SPT3=18.
SPT4=18
-- SPT5=20.
Corrected SPT Values

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given that

VIEW

Step 2: Calculation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through (9.42). Use K = 1.5 and Coyle and Castello’s method [Eq. (9.44)]
Compute the compressive force at the most stressed pile for each pile cap given in the table below. All column loads are unfactored and acting at the pile group centroid unless noted otherwise. My LL My (kN*m) y Pile Cap DL (kN)* LL(kN) LL Mx (kN*m) PC-1 1800 300 400 350 PC-2 1800 300 400 350 Mx *Pile cap weight is not included in the DL Notes: Pile diameter=600mm Use a pile cap thickness of 450mm for all cases with a conc unit wt of 23.5kN/m? PC-1 РС-2 3600 3600 1800 1800 1200 000 0081 009S
Give me right solution with clear calculations
A driven closed-ended pile, circular in cross section, is shown in Figure P12.7. Calculate the following. The ultimate point load using Meyerhof’s procedure. The ultimate point load using Vesic’s procedure. Take Irr = 50. An approximate ultimate point load on the basis of parts (a) and (b). The ultimate frictional resistance Qs. [Use Eqs. (12.42) through (12.44), and take K = 1.4 and δ′ = 0.6ϕ′.] The allowable load of the pile (use FS = 4).
A steel pile (H-section; HP 310 125; see Table 12.1a) is driven into a layer of sandstone. The length of the pile is 25 m. Following are the properties of the sandstone: unconfined compression strength = qu(lab) = 80 MN/m2 and angle of friction = 36. Using a factor of safety of 3, estimate the allowable point load that can be carried by the pile. Use [qu(design) = qu(lab)/5].
Solve Problem 12.23 using the method of Broms. Assume that the pile is flexible and free headed. Let the soil unit weight, = 16 kN/m3; the soil friction angle, = 30; and the yield stress of the pile material. FY = 21 MN/m2. 12.23 A 30 m long concrete pile is 305 mm 305 mm in cross section and is fully embedded in a sand dcposit. If nh = 9200 kN/m2, the moment at ground level Mg = 0, the allowable displacement of pile head = 12 mm; Ep = 21 106 kN/m2, and FY(pile) = 21,000 kN/m2, calculate the allowable lateral load, Qg, at the ground level. Use the elastic solution method.
U2
4. In which cases should the effect of negative frictional resistance on the pile side be considered?
Q # 1. Discuss in your own words with the help of diagram, the load transfer mechanism in skin resistance-end bearing piles. Subject: Geotechnical Design (CE-423)
17) The friction load capacity of the pile using the B-method is most nearly: a. 437 kN b. 927 kN c. 644 KN d. 1100 kN 15 m a. 177 kN b. 345 kN c. 441 kN d. 184 kN Groundwater table 381 mm NC Clay Yar 17 kN/m³ c²-0 kPa $-30° 23 t Sand Ysa 19.2 kN/m³ 18) In the previous question, the tip end-bearing load capacity of the pile using the B- method is most nearly: -28 e'=0 Tp2/3
Describe about the pile impedance.
Situation. A 15m precast concrete pile is to be lifted. If the unit weight of concrete is 23.54kN/m3 and the section of the pile measures 400mm by 400mm. Zoom image At what equal distance from the end should the pick-up point be located so that bending stress is minimum? O2.93m O 4.39m 3.75m O3.11m