Answered: DESIGN A PILE CAP USING THE STRUT AND…

DESIGN A PILE CAP USING THE STRUT AND MODELING METHOD. A 16"x16" precast concrete pile with pile capacity of 122kips, fc' = column load is 159.8kips. 5000psi, length of pile is 55' and the

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: interior column loads are 500 tons and pile groups are not to exceed eight, determine the cross-…

Q: to support a permanent axial load of 2200 kN and variable load of 1000 KN from a 500 x 500 mm…

A: According to given data permanent axial load of 2200 kN and variable load of 1000 KN from a 500 x…

Q: Calculate the pile point bearing capacity using Meyerhof's Method, where a Concrete pile of diameter…

A: The given data is: Diameter of concrete pile=12 in Length of pile=25 ft Unit weight of sand, γ=128…

Q: Determine ultimate carrying capacity of pile of diameter 0.3m and length 10m driven into sandy soil…

A: Diameter of the pile = D = .3mLength of the pile = L = 10mUnit weight of soil = γ = 17KNm2ϕ = 30°

Q: A 0.45m square pile is to be driven at a depth of 10m into the soil. What is the allowable pile…

A: B (size of pile) = 0.45m d (depth of pile) = 10m FOS = 3

Q: Why would it be inappropriate to use the Terzaghi bearing capacity formulas to determine the toe…

A: The ultimate load which a foundation can support is calculated by terzaghi bearing capacity…

Q: Q6) Determine the combined stress in HP 14 x 89 pile shown below. The pile is 25 feet long. E =…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Write a Short note on Statical Analysis (Single Pile Capacity).

A: Static Analytic Method Of Single Pile Capacity

Q: A 14-in.-diameter steel pipe pile is driven 50 ft into overconsolidated clays having the following…

A: The ultimate bearing capacity of the pile is given by,

Q: For a group of piles 3x5 with pile diameter is 0.4m and centre to centre spacing is 2.8 m,if the…

A: in given question , there is 3*5 pile with 0.4 m dia and 2.8 m spacing width of pile group=…

Q: -- Pile in Sand (friction and end bearing) Make calculations to determine the Allowable Load for a…

A: The objective of the question is to calculate the allowable load for a 14-inch square precast…

Q: A solid steel pile (E = 200 GPa) with uniform diameter of 100 mm is driven into a soil layer and…

A: The given data is as follows: E=200 GPaDiameter of pile=100 mmVertical force=40 kNFrictional…

Q: For a load of 1200 kN and assuming an overall factor of safety of 2.5, determine the required length…

A: the problem involves determining the required length of a pile for a given load and safety factor.…

Q: 3. As shown in the diagram, the RC solid precast square pile will be lifted up by two points, the…

Q: Q- A precast concrete pile is driven with a 50 kN hammer falling through a height of 1.0 m with an…

A: To find out the ultimate resistance of pile by modified hiley formula.

Q: O Calculate Lateral movement and Maximum moment of a 12" by 12" precast concrete single pile which…

A: Given: ϕ = 32o B = 12 in For sand: λ=1 For square section: R1 = 1.7 ε50=0.002

Q: Q-A precast concrete pile is driven with a 50 kN hammer falling through a height of 1.0 m with an…

Q: layer. Clay soil: c=40 kPa, Nc=7.5 Piles: Diameter = 350mm, Length=35m, Pile to pile spacing (center…

A: The question is based on the group of piles installed in the clay. The thickness of the pile cap,…

Q: 7.6 A dozer with as S-blade has pushed a normal load onto a level area. The height of this load…

Q: Calculate the side resistance in kips using the US Army Corps of Engineers (EM 1110-2-2906, Figure…

A: Given Data: Shear strength = 3752psf pile diameter = 14 in = 14/22ft = 1.167ft Length = 22ft

Q: A solid circular concrete pile is to be driven into a clayey soil with the following properties:…

A: Cu1 = 40 kPa Length (L1) = 5 m unit weight (γ1) = 15 kN/m3 Cu2 = 50 kPa Length (L2) = 10 m unit…

Q: 2. Three cast-in-place square piles with a side length of 700mm are installed under a certain…

A: Determine the properties of each soil layer. The properties of each soil layer are given in the…

Q: Describe the following briefly: (a) Negative Skin friction and its estimation. (b) Dynamic…

A: Negative skin friction or 'down drag' is a phenomenon, in which portion of a soil layer surrounding…

Q: Confirm the validity of statements by writing (T) otherwise write (F) and gave your opinion for it.…

A: Answer: Given statement is False (F)

Q: When we classify the piles in accordance to the type of loading, then we may call it as: *End…

A: Piles are vertical or slightly inclined, relatively slender structural foundation members. They…

Q: Calculate the combined settlement (81 + 82 + 83) of a single bored pile in a deep uniform clay layer…

Q: Find the best match between the 2 groups: 1. Drilled Piers 2. Drop Pile Hammer 3. Composite Pile…

A: The correct match is stated below.

Q: A- The load (Q=900 ton) locate at x, determine the max. & min. pile reaction for the given condition…

A: The pile is the supporting or substructure for the bridge or building when loading is acting due to…

Q: A pile is driven into the ground with a drop hammer weighing 1200 kg and having a free fall of 2.0…

A: Given data- Weight of drop hammer W=1200 kg, Free fall H=2 m=200 cm, Penetration S=1 cm, To Find-…

Q: 13. Among the following piles, which one does not belong to displacement pile ( B. Bored pile D.…

A: Displacement piles are defined as those piles that displace the soil laterally when they are…

Q: An HP 13 * 60 pile is made of steel with fy = 50 k/in2 and is to be loaded in compression only…

A: Calculate the maximum allowable compressive load on pile using the equation P = fu × A ..... (1)…

Q: For what purpose are the piles shown in the picture and prepared to hammer into the ground in the…

A: Polygoning Is the process of making polygon on field to take measurements along different lines

Q: A pile is driven into the ground with a drop hammer weighing 1200 kg and having a free fall of 2.0…

A: Given data- Weight of drop hammer W=1200 kg, Free fall H=2 m=200 cm, Penetration S=1 cm, To Find-…

Q: Discuss the ultimate load carrying capacity of the single pile when the pile embedded soil is; i)…

A: In Granular soils the ultimate load-carrying capacity: The pile drives load-carrying capacity from…

Q: Q3/ A 600 mm square prestressed concrete pile is to be driven to a depth of 20.0 m into the follow-…

A: Skin fraction capacity - QS QS = AsCa Here, As = 4×.6×18⇒As = 43.2 m2 And Ca = 35×5 + 55×5 + 6×85 +…

Q: b) A bored pile was installed in dense sand with the following data- kN/m The ground water table was…

A: Diameter of pile (d) = 0.6 mLength of pile( L) = 20 mAngle of internal friction(ϕ) = 30°γ = 20…

Q: Assuming a rigid pile, what is the minimum depth of penetration given a shear load of 894 lbs occurs…

A: Data Given: Shear force/Lateral Load = 894 lbse = 27 ftDiameter of the pile = 20 inches = 1.67 ftFOS…

Q: The following pile material provides the highest pile strength (per pile) OO Timber piles Steel…

A: Timber piles: The timber piles are used as a pile in the olden days. It should be free from pests…

Q: Determine the allowable bearing load of the pile shown in figure Q1 using all the possible methods…

A: The soil is cohesive. We will only need cohesive soil parameters.

Q: RL=105m V (U/s water level) RL=100m (D/s water level) 3m 6m Pile Pile 15m 10m 2m 8m For the above…

Q: Design a bored pile carrying a <OMpressive load of 1000 kN ¤nd a moment of 50 kNm. Use M25 mix And…

Q: Calculate the steel of spiral stirrups for a circular pile of X meter height where X is 133 and…

A: Spiral Stirrups of a Circular Pile Length of pile, L=133 m Diameter of pile, D=1.25 m Pitch of…

Q: The Young’s modulus of the concrete of the piles is 75.8 GPa and the concrete unit weight is 25…

A: E (Young's modulus of the concrete of the piles) = 75.8 GPaConcrete unit weight = 25 kN/m³Pile…

Q: Determine load carrying capacity of pile without considering critical depth concept. Diameter of…

A: Answer We know that the load bearing capacity of pile(Q) is given by combination of point Bearing…

Q: 15. The maximum vertical internal force of the pile section friction is at () resistance of pile…

A: The maximum vertical internal force of the pile section friction is at resistance of pile body at…

Q: A 650 mm diameter bored pile is driven into the ground until 30 m deep. The undrained shear…

Concept explainers

Pricing Excavation and Backfill

Backfill, in construction, is the activity of returning the soil and gravel that are removed during building construction or using them again to toughen and support the foundation of the building or any other structural component.

Question

DESIGN A PILE CAP USING THE STRUT AND MODELING METHOD. A 16"x16" precast
concrete pile with pile capacity of 122kips, fc' = 5000psi, length of pile is 55' and the
column load is 159.8kips.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given Data for the solution.

VIEW

Step 2: To find Area of the pile cap.

VIEW

Step 3: To determine dimensions based on the area of pile cap.

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A concrete pile is 15 m long and has 406 mm diameter circular cross section. The pile is fully embedded in sand, for which the unit weight '( = 18 kN/m3 and the frictional angle 8 = 30°. i) Calculate the ultimate point load Qp ii) Determine the total frictional resistance Qs iii) Determine the total ultimate load ofthe pile.
-- Pile in Sand (friction and end bearing) Make calculations to determine the Allowable Load for a 14-inch square precast concrete pile that is driven into a dense medium to fine sand deposit with = 36 deg. and y = 125 pcf. The pile is driven to 85 ft. depth, and there is still 40 ft. of sand below the pile tip. Groundwater is 6 ft. below ground surface. You are to assume that a static pile load test will be performed on one representative pile for this project. Use the limiting depth and limiting pressure approaches for end bearing and for side friction. State the K and 8 values you use, and justify.
A concrete pile group 3x3 with spacing of 0.6m is used to support a wind turbine in a sand deposit. Individual pile diameter = 0.3 m and length=6m. A. If the allowable (working) lateral capacity for a single pile is 95 kN, what is the maximum allowable lateral deflection for each pile? B. Is the lateral deflection acceptable? Explain your answer in 1-2 sentences.
A helical pile with 12 in diameter flights and a 2 in square rod is to be installed to a depth of 30 ft in a silty clay. The undrained shear strength is 1,000 lb/ft2 and the groundwater table is at a depth of 40 ft. The individual helixes are located every 5 ft along the length of the pile, and the pile has an average weight of 100 lb/ft (including the embedded soil). Using a factor of safety of 3, determine the ASD allowable uplift capacity, Pup,a.
The circular concrete pile (γc=23kN/m3) of Figure Q2 has dimensions which depend on the ultimate (j) and the penultimate (i) digit of your ID number as described by the formulae in Table Q2. It is constructed inside a sand with shear strength characteristics as given inTable Q2 as well. Calculate the safety factor for a working load equal to Q=300kN. Note : My ID Number is 9477287
Two different single acting hammers are being considered for an open- ended pipe pile. Hammer A has a ram weight of 30 kN and a stroke of 3 m. Hammer B has a ram weight of 15 kN and stroke of 5 m. Both hammers use similar appurtenances. Which hammer will deliver the most energy to the pile? Which hammer will generate the highest stresses in the pile?
A square prestressed concrete pile with a 14 inch side is to be driven to the necessary depth. It needs to be able to support 105 kips. It has been determined that the point resistance qp is 120 ksf and the side friction fs is 450 psf. Use formula 12.2 (see attached image) to estimate how long the pile needs to be with a factor of safety of at least 2.5. Round your answer to a multiple of 5 feet. Use L as a variable to calculate the load in formula 12.2. L can be obtained from this equation.