A concrete pile group 3x3 with spacing of 0.6m is used to support a wind turbine in a sand deposit. Individual pile diameter = 0.3 m and length=6m. A. If the allowable (working) lateral capacity for a single pile is 95 kN, what is the maximum allowable lateral deflection for each pile? B. Is the lateral deflection acceptable? Explain your answer in 1-2 sentences.

A concrete pile group 3x3 with spacing of 0.6m is used to support a wind turbine in a sand deposit. Individual pile diameter = 0.3 m and length=6m. A. If the allowable (working) lateral capacity for a single pile is 95 kN, what is the maximum allowable lateral deflection for each pile? B. Is the lateral deflection acceptable? Explain your answer in 1-2 sentences.

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.12P

See similar textbooks

Similar questions

Consider a 500 mm diameter pile having a length of 18 m in a clay. Given: γ = 20.0 kN/m3 and cu = 60 kN/m2. Determine the maximum allowable load (Qall) with FS = 3. Use the α method and Table 12.11 for determining the skin friction and Eq. (12.20) for determining the point load. Allow a factor of safety of 3. What percentage of the ultimate load is being carried by the pile shaft? Is it a friction pile?
Figure P12.36 shows a 3 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in length. What would be the maximum load that can be allowed on the mat with a factor of safety of 3? The piles have a center-to-center spacing of 1200 mm.
Determine the maximum load that can be allowed on the 450 mm diameter pile shown in Figure 18.36, with a safety factor of 3. Use the a method for computing the shaft friction. FIG. 18.36
Note: If your answer other than given options please leave it question.
A rectangular pile (0.5mx0.83m) is driven in a clayey soil arrangement composed of two different layers. The first layer has a height of 5m, cohesion of 58 kPa, friction factor of 0.84. Second layer has a height of 8m, cohesion of 76 kPa, and friction factor of 0.84. Compute the allowable load that the pile can carry if the factor it safety is 2.79.
A square prestressed concrete pile with a 14 inch side is to be driven to the necessary depth. It needs to be able to support 105 kips. It has been determined that the point resistance qp is 120 ksf and the side friction fs is 450 psf. Use formula 12.2 (see attached image) to estimate how long the pile needs to be with a factor of safety of at least 2.5. Round your answer to a multiple of 5 feet. Use L as a variable to calculate the load in formula 12.2. L can be obtained from this equation.
Q- Find the total load carrying capacity of a group of 9 piles with a group efficiency factor of 0.9. Given that the load carrying capacity of an individual friction pile is 200 kN.
A group of 25 HP 10 * 57 piles are arranged in a 5 * 5 grid at 27 inches on center and driven to a depth of 60 ft. The soil is a clay with unit side friction resistance, fn of 2000 lb/ft2 and a unit toe bearing resistance, q'n , of 15,000 lb/ft2. Determine whether individual or block failure controls the design, and determine the nominal capacity of the pile group, Png.
6) A 2-ft x 2-ft square concrete pile is shown. Ignore the resistance of the soft clay. Assume Na 10. For a safety factor of 3.0, the allowable load capacity of the pile is most nearly: a. 344 kips b. 169 kips c. 128 kips d. 225 kips 5 ft 30 ft R SOFT CLAY y=120 pcf SAND Y = 115 pcf =32°
A rectangular pile (0.52 x 0.82 m) is driven in a clayey soil arrangement composed of two different layers. First layer has a height of 7 m, cohesion of 55 kpa, friction factor of 0.89. Second layer has a height of 7 m, cohesion of 70 kpa, and friction factor of 0.87. Compute the allowable load that the pile can carry if the factor of safety is 2.11
Please solve it complete in one hour
Determine the maximum load that can be allowed on the 450 mm diameter pile shown in Figure P12.9, with a factor of safety of 3. Use the α method and Table 12.11 for determining the skin friction and Eq. (12.20) for determining the point load.