exampley Determine the ultimate load of closed ended pipe pile using the Static load test data of the fable below. Use Davission's and 10% relative settlement criteria. The outside diameter of the file is 355 mm, and total The steel cross sectional Length is 8.24 m. The steel use 200 GPa for area is 136.8 cm² Young's medulur. 1472 40t Axtattoodo 268 (KM) 515 669 803 936 10701204-1338 Settlement o 9.1 37 49 65 891 141 280,

Q: In a seismic design of a office building, calculate Base Shear V. Per seismic maps Ss=1.1g S 1 = 0.6…

A:

Q: 1. Check the compactness of W36x529, W21x48 and W14x99. 2. Verify the available flexural strength of…

A: The first part of the question is asking to check the compactness of the given steel sections.…

Q: What is the pile bearing capacity if the Downward drag = 0.6 psi, h1 = 30', h2 = 4', Frictional…

A: Downward drag = 0.6 psi, Height , h1 = 30',Height , h2 = 4',Frictional stress = 3.5psiAxial stress =…

Q: How does the effective stress method is considered superior from the total stress method for…

A: The two most commonly used method for studying the load support capacity of piles are : 1: α –…

Q: Find the force F in the image below such that the deep pile foundation under the structure frame…

A: Find Force F

Q: What is the pressuremeter test? Explain the procedure in brief with figures. How are its results…

A: Context: Pressuremeter test

Q: naximum shear stress in a beam of rectangular cross section is 50% larger than the r cross:

A: Dear students according to our company guidelines i can answer only first question. if you need…

Q: A static load test has been conducted on a 60 ft long, 16-in square reinforced concrete pile which…

A: Given settlement at head (ẟ1) = 1.211 in  settlement at A (ẟA) = 1.166 in  settlement at B (ẟB) =…

Q: An 18" square solid concrete pile is driven with an impact hammer to a depth of 55ft below grade…

A: Solution: Considering the Diagram: Qp=qpApqp=σvo'      Nq*≤0.5pa  Nq*tanφ…

Q: Describe about the pile impedance.

A: Pile impedance:

Q: 1. What is the difference between pre-tensioning and posst-tensioning in terms of prestress…

A: As per guidelines we need to answer only 1st question so please repost rest questions separately

Q: In Hiley’s formula for driven piles i.e. R=E/(s+0.5c), why is a coefficient of 0.5 applied for the…

A: Answer Hilley's Formula is based on the principle of energy of conservation.

Q: Based on Meyerhof’s (1956) suggestion, do you think a mechanical or electrical cone penetration…

A: Following is required answer :

Q: A drop hammer is used to drive a wooden pile The hammer weight is 25 N and its free falling height…

A:

Q: 10 A pile of 40cm diameter and 18.5m -long passes through two layers and embedded in a third layer.…

A:

Q: 17) The friction load capacity of the pile using the B-method is most nearly: a. 437 kN b. 927 kN c.…

A: To determine- Friction load capacity

Applications of Concrete Framing Systems

A concrete frame is a structure formed by the interconnection of beams and columns to form a structural network. In simple terms, it is the basic skeletal structure of a building or any construction. The concrete framing structure is built on a concrete foundation that forms the base of the entire structure. The concrete frame system is built to support floors, roofs, walls, beams, rafters, joists, etc.