For a load of 1200 kN and assuming an overall factor of safety of 2.5, determine the requiredlength of the pile.If the pile is bored, what modification to design parameters would you have done indetermining the pile length?

the problem involves determining the required length of a pile for a given load and safety factor.…

Answered: For a load of 1200 kN and assuming an…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

DESIGN A PILE CAP USING THE STRUT AND MODELING METHOD. A 16"x16" precast concrete pile with pile capacity of 122kips, fc' = 5000psi, length of pile is 55' and the column load is 159.8kips.
Calculate the side resistance in pounds for a 20 ft long open ended 27 inch diameter smooth steel pipe pile driven in sand with a friction angle of 35 degrees using the beta method. Assume the water table is at the ground surface. The unit weight of the soil is 126 pcf. The overconsolidation ratio is one.
A 16 in diameter, 75 ft long drilled displacement pile is made of grout with f'c = 5,000 lb/in2. A steel ratio of 0.04 is to be used in the upper 30 ft, and a steel ratio of 0.001 for the remainder of the pile. Compute the modulus of elasticity for the upper and lower portions of this pile.
The ultimate load capacity of a 12 m long concrete pile of square cross section 600 mm x 600 mm driven into a homogeneous clay layer having undrained cohesion value of 50 kPa is 900 KN. If the cross-section of the pile is reduced to 400 mm x 400 mm and the length of the pile is increased to 20 m, the ultimate load carrying capacity will be
-- Pile in Sand (friction and end bearing) Make calculations to determine the Allowable Load for a 14-inch square precast concrete pile that is driven into a dense medium to fine sand deposit with = 36 deg. and y = 125 pcf. The pile is driven to 85 ft. depth, and there is still 40 ft. of sand below the pile tip. Groundwater is 6 ft. below ground surface. You are to assume that a static pile load test will be performed on one representative pile for this project. Use the limiting depth and limiting pressure approaches for end bearing and for side friction. State the K and 8 values you use, and justify.
A concrete pile group 3x3 with spacing of 0.6m is used to support a wind turbine in a sand deposit. Individual pile diameter = 0.3 m and length=6m. A. If the allowable (working) lateral capacity for a single pile is 95 kN, what is the maximum allowable lateral deflection for each pile? B. Is the lateral deflection acceptable? Explain your answer in 1-2 sentences.
A square prestressed concrete pile with a 14 inch side is to be driven to the necessary depth. It needs to be able to support 105 kips. It has been determined that the point resistance qp is 120 ksf and the side friction fs is 450 psf. Use formula 12.2 (see attached image) to estimate how long the pile needs to be with a factor of safety of at least 2.5. Round your answer to a multiple of 5 feet. Use L as a variable to calculate the load in formula 12.2. L can be obtained from this equation.
Please solve and mention answer

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

For a load of 1200 kN and assuming an overall factor of safety of 2.5, determine the required length of the pile. If the pile is bored, what modification to design parameters would you have done in determining the pile length?