A- The load (Q=900 ton) locate at x, determine the max. & min. pile reaction for the given condition shown in figure below. (All dimensions in meter) |0 1.0 1.0 5.0 m to 3.0 3.0 5.0m 3.0 1.0i 1.0' 3.0 O-

A- The load (Q=900 ton) locate at x, determine the max. & min. pile reaction for the given condition shown in figure below. (All dimensions in meter) |0 1.0 1.0 5.0 m to 3.0 3.0 5.0m 3.0 1.0i 1.0' 3.0 O-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 6) A 2-ft x 2-ft square concrete pile is shown. Ignore the resistance of the soft clay. Assume Nq=…

A: B = 2 ft Nq = 10 FS = 3

Q: 2. Determine the allowable load carrying capacity of the pile shown below. The average unit skin…

A: Given that, average unit skin resistance = 1.2kN/m2 unit point resistance = 30kN/m2 FS=3.0 length…

Q: H.O 9 A 20-m-long concrete pile is shown in Figure below. Estimate the ultimate point load Q, by a.…

A: Given concrete pile Length=20m Size=460×460mm

Q: Estimate the pile length required to carry the 900 kN axial load for the pile-soil system shown the…

A: Given the details of Soil profile as:Soil 1:C= 35 kPaSoil 2:C= 45 kPaSoil 3:C= 55 kPaSoil 4:C= 60…

Q: Consider a precast concrete pile that is 0.505 m X 0.505 m in cross section driven in a homogeneous…

A: The following are the given information, Pile Cross section = 0.505 m x 0.505 m Homogeneous sand…

Q: Determine ultimate carrying capacity of pile of diameter 0.3m and length 10m driven into sandy soil…

A: Diameter of the pile = D = .3mLength of the pile = L = 10mUnit weight of soil = γ = 17KNm2ϕ = 30°

Q: The length of the pile required for the above design load

A: This question is from geotechnical engineering

Q: A 12 inch diameter concrete pile is to be driven into a clay deposit as shown in Figure 2. The…

Q: Calculate the load bearing capacity of the pile shown in Figure Q5. Assume that it is a bored pile,…

A: Given, L = 18.5 m B = 0.60 m

Q: a. The ultimate point load using Meyerhof's procedure. b. The ultimate frictional resistance Qs.…

Q: 2. A 0.45 m diameter, 20 m long, precast concrete pile is driven into a sandy soil profile. The SPT…

A: ###DETERMINATION OF Ultimate bearing Capacity of Driven Pile into a Sandy Soil wih SPT value given…

Q: (a) Determine the allowable load-carrying capacity of the bored concrete pile for: embedded length =…

Q: A square concrete pile12m long is shown in Figure. Estimate the following: Ultimate shaft carrying…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: 13) A cylindrical pile of diameter 0.3 m is driven to a depth of 15 m in to an NC clay as shown in…

A: Given; Diameter of pile (d) =0.3 m Depth of the pile (l) = 15 m Factor of safety (Fs) = 3

Q: Assume the curve shown in Figure 14.14 has been obtained from a static load test on a 60 ft long,…

Q: A Flownet has been drawn as shown in the figure. Point A and C are at elevation h, and he…

A: Determine the:a. compute the piezometric pressure at point A in kPa. b. compute the piezometric…

Q: A 16 in diameter, 55 ft long drilled displacement pile is to be constructed in the following soil…

A: Calculate the Toe Bearing capacity: The construction method for DD piles does not provide any…

Q: c. Coyle and Castello's method Use m= 600 in Eq. (12.28). Concrete pile 460 mm x 460 mm Loose sand…

A: Solution; Given that; long =20 m Concrete pile 460 mm×460 mm

Q: A pile of diameter 457 mm is fully embedded in a clay strata as shown in figure. C- 25 kN/m y= 16…

Q: Determine the ultimate bearing load of the pile using Tomlinson for a 12.5-m closed-end steel pipe…

Q: Refer to Figure 9.42b. Let L = 18 m, γfill = 17 kN/m3, γsat(clay) = 19.8 kN/m3, Φ'clay = 20°, Hf =…

A: The downward drag force will be: Qn=pK'yf Hf tanδ'L1+L12pK'y'tanδ'2 ...(1)The neutral…

Q: Solve Problem 9.16 with the following: length of pile = 15 m, pile cross section = 0.305 m x 0.305…

A: Calculate the elastic settlement by using the equation Se=Se1+Se2+Se3…

Q: For the pile distribution below, determine the load Pp that the red pile will receive, in Ton. P=254…

A: given:d= 2 mex=0.2 mey=0.3 mH=1.3 mP=254 ton

Q: Find the maximum pile capacity for the pile group shown in figure below. If My = 500 kN.m and V =…

A: Given bending moment about y axis My=500 KN.mAxial force V=1500 KNno. of piles n=9

Q: P-2 A 21.4-m-long HP 360*174 steel pile is 20m-embedded in a clay deposit and 1.4m above ground (…

Q: Nine-pile group consists of 0.28-meter-diameter friction concrete piles 24m long arranged in 3 rows…

Q: P-2 A 21.4-m-long HP 360*174 steel pile is 20m-embedded in a clay deposit and 1.4m above ground (…

Q: X XXXX 4m 5m 6 m XX Key: PILE I Soil 1 c = 35 kPa Y = 16.79 kN/m³ Soil 2 GROUND LEVEL Soil 3 c = 45…

A: Soil profile:Soil 1:C= 35 kPaSoil 2:C= 45 kPaSoil 3:C= 55 kPaSoil 4:C= 60 kPa

Q: o Given: A earth pile with L, E, and A known and constant F Y X (L-x) steel pile soil f =…

Q: For the pile distribution below, determine the load Pp that the red pile will receive, in Ton. P =…

A: Step 1

Q: Calculate the allowable axial load for the driven pile of ( 0.5 m) dia. And ( 20 m) depth, in a…

A: Solution: “Since you have asked multiple questions, we will solve the first question for you. If you…

Q: 4. Calculate the lateral force of a wall of height 20 ft with a sand backfill as shown in figure.2.…

Q: Q3 The system shown in figure find the following: a-flow rate per meter length of sheet pile ,if k=…

A: K=1x10-4 m/sec, L=1.5 m, Void ratio(e)=0.57, Specific gravity(G)=2.68.

Q: Q3: B- : For a given flow net of water flow around a sheet pile in Figure below, if the critical…

A: Given Critical hydraulic gradient= 0.941

Q: QUESTION 3 A concrete pile is driven into top two layers of subsoil strata made of 10m and 5m thick…

A: Given data: diameter of pile = 0.5 m clay layer 1: Height = 10 m saturated unit weight = 18 kN/m3.…

Q: Variation of N60 with depth in a granular soil deposit is given below. A concrete pile 9 m long with…

A: Allowable load on pile The position of the groundwater table affects the ultimate capacity of piles…

Q: A pre cast pile having a cross section of 0.20m x 0.200 is placed at a position as shown in the…

Q: A 11-in. square concrete pile is driven into a clay deposit as shown in the figure below. The unit…

A: A concrete pile of length, L 40 ft and 11 in square concrete pile is embedded in the clay soil. The…

Q: A rectangular pile (0.5mx0.83m) is driven in a clayey soil arrangement composed of two different…

Q: A concrete pile 458 mm by 458 mm square cross section is embedded in a saturated clay. The length…

A: Given data- A concrete pile 458 mm by 458 mm square cross-section. Saturated clay. The length of the…

Q: Q2 : For the circular bar shown in figure, subjected to uniformly distributed load (f kN/m) along…

Q: QUESTION 3: Three forces act on a pile as shown. If the resultant of the three forces is equal to…

A: An arrangement of forces have been given and it has been asked to determine missing force and its…

Q: Consider a drilled, rough concrete pile with diameter B = 1m and length D = 10m embedded in a site…

Q: d. Starting out from the condition where the water table is above the excavation line on both sides…

A: Brief concept introduction- Sheet Pile- Sheet piles are used to support earth retention and…

Q: Determine the design capacity of the pile group shown below. The pile cap thickness is 1.5 meters,…

A: Given, Diameter of piles= 350 mm Length of piles= 12 m K=3 αc=0.5 FOS=3 Number of piles= 6…

Q: A driven closed-ended pile, circular in cross section, is shown in Figure P 9.4.Calculate the…

A: Given:- Irr = 50. c'=0 width =381mm To find:- a. The ultimate point load using Meyerhof’s…

Q: Determine the consolidation settlement of piles group shown below. Sand y = 105 lb/ft³ Groundwater…

Concept explainers

Pricing Excavation and Backfill

Backfill, in construction, is the activity of returning the soil and gravel that are removed during building construction or using them again to toughen and support the foundation of the building or any other structural component.

Question

A- The load (Q-900 ton) locate at x, determine the max. & min. pile reaction for the given
condition shown in figure below.
(All dimensions in meter)
| 1.41.0
5.0 m
to
3.0
3.0
5.0m
3.0
1.0i 1.0 3.0

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

In-situ stresses - Seepage condition ground level sheet piling. Example: For the sheet pile which is buried in sandy soil ,shown in 20m the figure below, find the total water level and effective vertical stress at Points 0, 6, and 12?. 4.0m Note: Assume reasonable values for saturated and dry unit weight equipotential datum 12 of the soil Col 3.0 m 10 flow line 3.0m Soil Mechanics II: Lecture 2
17) The friction load capacity of the pile using the B-method is most nearly: a. 437 kN b. 927 kN c. 644 KN d. 1100 kN 15 m a. 177 kN b. 345 kN c. 441 kN d. 184 kN Groundwater table 381 mm NC Clay Yar 17 kN/m³ c²-0 kPa $-30° 23 t Sand Ysa 19.2 kN/m³ 18) In the previous question, the tip end-bearing load capacity of the pile using the B- method is most nearly: -28 e'=0 Tp2/3
Problem 1 Pre-stressed concrete piles are planned for use as the foundation for a waterfront structure. Soil condition is dense sand and no water table below the ground. Properties of soil: y = 19.65 kN/m³ k=3 tan a = 0.45 N₂-80 Consider a single 30 cm square pile driven 9m below the ground with critical depth of 6m. Determine the following: a. Capacity of pile due to skin friction b. Capacity due to end bearing C Design load that the pile could carry if the factor of safety is 3.
Esample: - A cantilever shet pile wall penetrating granular soil is shown in Figure below. Deternmine: (a) The depth of the embedment, D. using a flactor of safety of 1.5. (b) The inaximum moment on the sheet pile. y- 17 AN/m 1-3m Dredge lia
In-situ stresses - Seepage condition ground level Example: For the sheet pile which is buried in sandy soil ,shown in the figure below, find the total and effective vertical stress at Points 0, 6, sheet piling. 2.0m water level 4.0m and 12?. Note: Assume reasonable values for equipotential datum saturated and dry unit weight of the soil 3.0 m 10 flow line 3.0m Soil Mechanics II: Lecture 2 8
A pile of diameter 0.4 m is fully embedded in a clay stratum having 5 layers, each 5 m thick as shown in the figure below. Assume a constant unit weight of soil as 18 kN/m³ for all the layers. Using method (= 0.15 for 25 m embedment length) and neglecting the end bearing component, the ultimate pile capacity (in kN) is G Y=18kN/m³- for all layers 7XXX 5m 5m 5m 5m 5m = 25 m 0.4m, c=40 kPa c=50 kPa c=60 kPa c=70 kPa c=80 kPa S XXXX
A concrete pile 0.133ft by 0.133ft in cross section is shown below. Pile length 10 m . Answer a) ii, iii, iv
Determine the allowable load capacity of the 0.4 m diameter pile shown in Figure 4. The fill is new and unconsolidated. A steel shell is proposed around the pile within the fill layer to eliminate the negative friction. The ground water level is at the middle of the fill layer. Use a factor of safety of 2.5. (y=moist unit weight; ysat=saturated unit weight) Steel shell Fill layer Ysat = 17 kN/m, Y=16 kN/m³ O'= 30° K=1.2 8'=0.86' 4 m %3D Clay (overconsolidated) Ysat = 19.5kN/m³ 10 m PR' = 30° 8'=0.6¢R' Sand Ysat = 18 kN/m³, y = 16.5 kN/m3 O'= 30° K=1.3 18 m 8'=0.86' 0.5 m
A 10m long and 0.8m diameter precast concrete pile is driven into a saturated clay deposit as shown in the figure below. The groundwater table is at the ground surface. For the ratio of the undrained shear strength to vertical effective pressure is approximated as follows: = 0.11 + 0.0037(PI) NC (9- 9 (OCR)8 OC Determine the bearing capacity for the pile by the a) Alpha (a) method. b) Lambda (A) method Depth, m Layer 1 OCR = 5, Yat = 19.5 kN/m³, Pl = 35 Layer 2 OCR = 1.5, %at = 19.0 kN/m, Pl = 25 Layer 3 OCR = 8, %at = 19.5 kN/m, Pl = 20 10 D, = 0.8 m D 10 m
In the soil illustrated in the picture below, a 60-foot-long drilled pile is to be built using the open hole method. The pile will be 24 inches in diameter, and the bottom will be 60 inches in diameter. The soil conditions are homogeneous. Determine the allowable downward load capacity using a method. (The soil is in dry condition) (All the measurements are in feet) -1.5 Stiff silty clay Y = 105 lb/ft3 Su = 1600 lb/ft² Stiff silty clay Y = 108 lb/ft³ Su 1400 lb/ft² T Very Stiff silty clay y = 109 lb/ft³ Su = 4000 lb/ft² 12 25 23
A concrete pile is 15 m long and has 406 mm diameter circular cross section. The pile is fully embedded in sand, for which the unit weight '( = 18 kN/m3 and the frictional angle 8 = 30°. i) Calculate the ultimate point load Qp ii) Determine the total frictional resistance Qs iii) Determine the total ultimate load ofthe pile.
FDE 015: A group of friction piles is shown. The total load on the pile less the soil displaced by the footing is 1900 kN. Lp = 2 m, L2 - 1.8 m, L = 12 m, t = 19 m, 9u = 180 kPa, FS = 3. See figure below. Compute for the compression index of the day.