Determine the allowable load carrying capacity of the pile shown below.The average unit skin resistance is 1.2kN/m2, and the unit point resistance is 30kN/m2. Use FS=3.0 2. Determine the allowable load carrying capacity of the pile shown below. Theaverage unit skin resistance is 1.2kN/m?, and the unit point resistance is 30KN/m?.Use FS=3.0.G.L.10mConcrete pile250mm x 250mm

Given that, average unit skin resistance = 1.2kN/m2 unit point resistance = 30kN/m2 FS=3.0 length…

2. Determine the allowable load carrying capacity of the pile shown below. The average unit skin resistance is 1.2kN/m?, and the unit point resistance is 30KN/m?. Use FS=3.0. G.L. 10m Concrete pile 250mm x 250mm

2. Determine the allowable load carrying capacity of the pile shown below. The average unit skin resistance is 1.2kN/m?, and the unit point resistance is 30KN/m?. Use FS=3.0. G.L. 10m Concrete pile 250mm x 250mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 6) A 2-ft x 2-ft square concrete pile is shown. Ignore the resistance of the soft clay. Assume Nq=…

A: B = 2 ft Nq = 10 FS = 3

Q: 1. An HP 250x84.98 steel pile is driven into sand as shown. Determine the frictional resistance if…

Q: a Pile have diameter of 0.4 m and ultimate pile capacity 12000 Kn, F.s=3 if the load will applies =…

Q: Question 12 A rectangular pile (0.65 x 0.53 m.) is driven in a clayey soil arrangement composed of…

Q: A prestressed concrete pile, 482 mm in diameter, is to be driven in a clayey soil. The pile has a…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: Q6) Determine the combined stress in HP 14 x 89 pile shown below. The pile is 25 feet long. E =…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Q3: What is the ultimate capacity of 4x4 concrete pile group shown in figure 3. The pile diameter…

A: Sheet piles are metal parts with interlocking edges driven into the ground to provide permanent or…

Q: A 0.5 x 0.5 m square concrete pile is to be driven in a homogeneous clayey soil having undrained…

Q: The ultimate load capacity of a 10 m long concrete pile of square cross section 500 mm x 500 mm…

A: Solution: The correct option for above question is (B) i.e 632.5 kN For Pile 1 Ultimate load…

Q: A rectangular pile (0.91 x 0.54 m.) is driven in a clayey soil arrangement composed of two different…

A: To determine the allowable load that the pile can carry. The bearing capacity of a pile is…

Q: Check the total settlement of a group of pile as shown in Figure 1. The to set not exceed 3% of the…

Q: rectangular pile (0.54 x 0.63) is driven in clayey soil arrangement composed of two different…

Q: and thereafter, Cu 132, 32, where z is the depth Z IS each strata. Determine the ultimate capacity…

Q: Determine the base capacity of a square pile with a 0.4 m width and a 10 m length using Hansen's…

Q: A pile of diameter 457 mm is fully embedded in a clay strata as shown in figure. C- 25 kN/m y= 16…

Q: Qu= qbAb + αcu,ave As qb= CuNc* Depth (m) 1 3 5 7 9 11 13 Table 1: Strength profile 15 17 19 21 Cu…

Q: A 0.36 m. square pre-stressed concrete pile is to be driven in a clay soil having an unconfined…

A: Prestressed concrete pile: Prestressed concrete is mostly used in low and medium-rise buildings…

Q: A timber pile 400 mm in diameter is subjected to the following axial compressive loads: dead =600…

A: Solution Given Data Diameter= 400 mm Dead load= 600 kN Live load= 250 kN earthquake=200 kN Allowable…

Q: A prestressed concrete pile, 475 mm in diameter, is to be driven in a clayey soil. The pile has a…

A: NOTE :- Since, it is not given the type of pile so taking it as both end bearing and friction pile.…

Q: A drop hammer is used to drive a wooden pile. The hammer weight is 30 kN and its free falling height…

A: Given data,For drop hammer is used to drive a wooden pileWeight of hammer=30 kNFalling height =0.9…

Q: A precast circular pile (like a concrete rod) of length Land diameter D is to be lifted at two…

Q: layey so friction factor of 0.81. Compute the allowable load that the pile can carry if the factor…

Q: A concrete pile of size 50 cm x 50 cm is to be provided in a clay stratum vhose unconfined…

A: Size = o.4mx0.4m load = 450 UCS unconfined compressive strength = 110kpa Hence c = 110/2 = 55…

Q: A 11-in. square concrete pile is driven into a clay deposit as shown in the figure below. The unit…

A: A concrete pile of length, L 40 ft and 11 in square concrete pile is embedded in the clay soil. The…

Q: The average values of the undrained shear strength (c,) with depth are given as follows: Depth (m) ,…

A: The length of the pile lies between the 8 m to 12 m. So, cu=80 kN/m2 The empirical adhesion factor…

Q: Calculate maximum load applying in the pile of the 9-pile group below (P= 9000 kN, M=2000 kNm) 1.2m…

A: This problem is related to Pile foundation from Soil Mechanics. In this problem given about Load and…

Q: A rectangular pile (0.5mx0.83m) is driven in a clayey soil arrangement composed of two different…

Q: Q2 : For the circular bar shown in figure, subjected to uniformly distributed load (f kN/m) along…

Q: 3. A jnven closed-ended pjle, circular in cross section, is shown. Calculate the following. a. The…

A: Given, Pile diameter (D) = 381 mm or 0.381 m Pile length (L) = 21 m

Q: 12 m c=0 Y = 16.8 kN/m³ $ F = 1.4 Dr=0.80 = 35° -30.5 cm

A: Spacing= 2.5 m Angle of friction= 35°

Q: Determine the allowable bearing load of the pile shown in figure Q1 using all the possible methods…

A: The soil is cohesive. We will only need cohesive soil parameters.

Q: A circular concrete pile 350 mm in diameter is to support a load of 270kN.Itis driven in a stiff…

A: given diameter of pile (D)= 350 mm given diameter of pile (D)= 0.350 m area of pile cross section =…

Q: In a 16 (4 x4) piles group, the pile diameter is 0.4 m and center to center spacing of piles in the…

Q: 1) A precast concrete pile with a cross-section of 350mm x 350mm is embedded in sand. The length of…

A: The given information is Size of pile350×350mm φ=350 L=15 m γsand=15.8 kN/m2 The relative density…

Q: Estimate the pile length required to carry the 670 kN axial load for the pile-soil system shown in…

A: Axial load, Pa = 670 kNPile diameter, D = 460 mmSafety factor = 3.0

Q: Calculate the pile's allowable bearing load using the corrected SPT values at various depths given…

Q: 0.5 m diameter concrete pile is driven at a site as shown in Figure below. What is the pile's…

A: Terzagi bearing capacity factor chart:

Q: Q Y- 17.5 kN/m Cohesion = 28 kPa a - 0.95 Y= 17.8 kN/m w = 25% & Gs = 2.6 Cohesion = 35 kPa a = 0.85…

Q: A 650 mm diameter bored pile is driven into the ground until 30 m deep. The undrained shear…

Q: 1. A1 ft x 1 ft size and 30 ft deep concrete pile is to be driven in the clay layer shown in the…

A: Size of footing A=1×1=1 ft2depth of pile cap =3 ftthen length of footing 17 ft in soil A and 30…

Concept explainers

Measuring site work, Excavation and Piling

Bid drawings typically include very little material about the precise requirements of site work operations, measuring site work and excavation work differs from measuring most other works on a construction project. The actual site work conditions are not provided and also the dimensions of the excavations are not known during the pre-construction phase. The precise measurement of the excavation and backfill of the earth material and topsoil is important for a contractor to decide upon the total cost required for the process. All the works should be carried out under OSHA (Occupational Safety and Health Administration) standards to ensure the safety of the workers.

Question

Determine the allowable load carrying capacity of the pile shown below.

The average unit skin resistance is 1.2kN/m2, and the unit point resistance is 30kN/m2. Use FS=3.0

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Measuring sitework, excavation and piling

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 10m long and 0.8m diameter precast concrete pile is driven into a saturated clay deposit as shown in the figure below. The groundwater table is at the ground surface. For the ratio of the undrained shear strength to vertical effective pressure is approximated as follows: = 0.11 + 0.0037(PI) NC (9- 9 (OCR)8 OC Determine the bearing capacity for the pile by the a) Alpha (a) method. b) Lambda (A) method Depth, m Layer 1 OCR = 5, Yat = 19.5 kN/m³, Pl = 35 Layer 2 OCR = 1.5, %at = 19.0 kN/m, Pl = 25 Layer 3 OCR = 8, %at = 19.5 kN/m, Pl = 20 10 D, = 0.8 m D 10 m
20 A rectangular pile (0.75 x 0.93 m.) is driven in a clayey soil arrangement composed of two different layers. First layer has a height of 5 m., cohesion of 53 kPa, friction factor of 0.88. Second layer has a height of 8 m., cohesion of 78 kPa, and friction factor of 0.84. Compute the allowable load that the pile can carry if the factor of safety is 2.17. Round off to two decimal places.
Note: Read the question carefully and give me right solution according to the question. A pile is made of recycled aggregate material. The pile has a diameter of 95 ft. at the base, and30 ft. at the top. It is 23 ft. high. The volume of the pile (yd3) is most nearly: a ) 1,350b ) 89,643c ) 2460d ) 3320
Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement is set not exceed 3% of the pile diameter and the overconsolidated ratio (OCR) of the clay is more than 1. The groundwater table is located 15m beneath the ground level. The diameter of the pile, b is 0.5m and the spacing between piles, s is 2m.The pile group is subjected to foundation load of 5425kN. The laboratory testing data for the soil samples taken are as follows: At 5m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 150kN/m? At 10m, eo = 0.55, Cc = 0.32, Cs = 0.09, o'o = 225kN/m2 %3D At 12m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 300KN/m2 %3D 7m 5m Clay 3 10m Unit weight = 18KN/m %3D Friction angle = 0 degree 2 Cohesion = 100KN/m
Two different single acting hammers are being considered for an open- ended pipe pile. Hammer A has a ram weight of 30 kN and a stroke of 3 m. Hammer B has a ram weight of 15 kN and stroke of 5 m. Both hammers use similar appurtenances. Which hammer will deliver the most energy to the pile? Which hammer will generate the highest stresses in the pile?
A circular pile is to be driven upto a depth of 10 m at a construction site. The average surface area of the pile is 2 m2 per meter length. The soil at the site is homogeneous sand, having effective friction angle of 30°. The ground water table (GWT) is at a depth of 4 m below the ground surface. The unit weights of the soil above and below the GWT are 18 kN/m3 and 20 kN/m3 respectively. Takek = 0.9 and the angle of wall friction (6) = 28°. The total axial frictional resistance mobilized on the pile against the driving is %3D kN. (Y = 9.81 kN/m³) %3D
Situation 5 - A rectangular pile (0.77 x 0.72 m.) is driven in a clayey soil arrangement composed of two different layers. First layer has a height of 7 m., cohesion of 53 kPa, friction factor of 0.89. Second layer has a height of 8 m., cohesion of 78 kPa, and friction factor of 0.88. (A.) Compute the skin friction resistance in kN. Round off to two decimal places. (B.) Compute the end bearing capacity in kN. Round off to two decimal places. (C.) Compute the allowable load, in kN, that the pile can carry if the factor of safety is 2.00. Round off to two decimal places.