Q2 : For the circular bar shown in figure, subjected to uniformly distributed load (f kN/m) along its length . The length (L) and diameter of pile (D) and modulus of elasticity (E) are given in Table below, find the displacement at point (A). Name L(m) f(kN/m) D (mm) 100 Case (Gpa) 40 No. فرق عباس 2

Q2 : For the circular bar shown in figure, subjected to uniformly distributed load (f kN/m) along its length . The length (L) and diameter of pile (D) and modulus of elasticity (E) are given in Table below, find the displacement at point (A). Name L(m) f(kN/m) D (mm) 100 Case (Gpa) 40 No. فرق عباس 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The distributed load shown is supported by a box beam shown using five pieces of 50mm x 300mm plank of Yacal timber arrange as shown. Determine the nearest maximum safe value of w in N/m that will not exceed a shearing stress of 1.2MPa. WIN 6m¶ 1.5m¶
Pls provide hand written solution
A 1m RB B 2m C 153 kN/m 2 m D 28 KN 3m 19 kN/m E RE 2 m Question: Compute the shear diagram of the given load diagram F
determine the tensile development lengths required using: (a) ACI Metric Equation 25.4.2.3a, assuming Ktr = 0, and (b) ACI Metric Equation 25.4.2.3a and the computed value of Ktr . Use fy = 420 MPa and fc′ = 28 MPa.
The wooden pile shown in the figure has a diameter of 95 mm and is subjected to a load of P = 80 kN. Along the length of the pile and around its perimeter, soil supplies a constant frictional resistance of w = 2.90 kN/m. The length of the pile is L = 5.6 m and its elastic modulus is E = 8.6 GPa.Calculate(a) the force FB needed at the base of the pile for equilibrium.(b) the magnitude of the downward displacement at A relative to B.
PILE FOUNDATIONS • Example: 35/1 A machine foundation is supported by four prestressed concrete plies driven to bedrock. The length of each pile is 24 m, and they are 0.3 mx 0.3 m in cross section. The weight of the machine and the foundation is 1360 kN. Given: unit weight of concrete = 24 kN/m¹ and the modulus of elasticity of the concrete used for the piles = 24.5 × 106 kPa. Determine the natural frequency of the pile foundation system.
The wooden pile shown in the figure has a diameter of 105 mm and is subjected to a load of P = 70 kN. Along the length of the pile and around its perimeter, soil supplies a constant frictional resistance of w = 3.85 kN/m. The length of the pile is L = 4.0 m and its elastic modulus is E= 12.9 GPa. Calculate (a) the force Fg needed at the base of the pile for equilibrium. (b) the magnitude of the downward displacement at A relative to B. y L Answers: (a) FB = (b) UA= i i B FB KN mm
I need detailed explanation to solve the exercise below. There are some formulas and hints, I also added some tables from the book.Meyerhof's method, Coyle and Castello's method and Vesic's method were already solved.
Question 12 . A commercial building assigned to SDC D has a fundamental period of 0.4 seconds, Sps = 1.0g, Sp=0.55g, R = 6, and W = 1,000,000 pounds. What is the DS base shear? A. 114 kips B. 121 kips 167 kips 209 kips C. D. COAA OB, B OC.C D.D
A column in the upper story of a building is subjected to a compressive load from the followingsources: dead load = 30.8 kips, occupancy live load = 1.7 kips, roof live load = 18.7 kips, and snowload = 19.7 kips.a. If load and resistance factor design (LRFD) is used, determine the factored load (requiredstrength) to be used in the design of the column. Which ASCE load combination controls?b. What is the required design strength of the column?c. What is the required nominal strength of the column for a resistance factor phi of0.9?d. If allowable strength design (ASD), determine the required load capacity (requiredstrength) to be used in the design of the column. Which ASCE load combination controls.e. What is the required nominal strength of the column for a safety factor Omega of 1.67.
Problem 2 4" For the problem below, 600 lb (1) Plot V&M diagram using graphic method (2) Calculate shear stress 300 Ib/ft Tm and tn at 8' from A (3) Plot shear stress B 200 lb/ft DA 8" 10' 5' distribution at 18' 6' 900 lb 1500 lb from A 1" Note: the uniformly distributed load 200 lb/ft is upwards and 300 Ib/ft is downwards 5600 ft-lb 3500 ft-lb
Determine the amount of axial shortening that the friction pile undergoes in service. Assume that the surface (or “skin”) friction f (force/lenth2) varies as shown and that E and A are constant.