L13L/2L/2B.AProb. 5 (10 points) The figure shows a drill-rig pipe that is being picked up by a crane atpoint C. The pipe has dimensions L= 32 ft., do = 4. 50 in., and d; = 3. 60 in., and weighs21 lbf/ft. At the moment when 0 = 30°, please calculate the principal stresses at: (a) thepoint marked B, and (b) at the point given by z = 0, y = do/2 at the same cross-section (i.e.at L/2 from the point A).

Answered: Image /qna-images/answer/f4a634b9-b47f-4cac-894b-9945277fef0f.jpg

L/3 L12 L/2 Prob. 5 (10 points) The figure shows a drill-rig pipe that is being picked up by a crane at point C. The pipe has dimensions L= 32 ft., do = 4. 50 in., and d; = 3.60 in., and weighs 21 lb;/ft. At the moment when 0 = 30°, please calculate the principal stresses at: (a) the point marked B, and (b) at the point given by z = 0, y = d/2 at the same cross-section (i.e. at L/2 from the point A).

L/3 L12 L/2 Prob. 5 (10 points) The figure shows a drill-rig pipe that is being picked up by a crane at point C. The pipe has dimensions L= 32 ft., do = 4. 50 in., and d; = 3.60 in., and weighs 21 lb;/ft. At the moment when 0 = 30°, please calculate the principal stresses at: (a) the point marked B, and (b) at the point given by z = 0, y = d/2 at the same cross-section (i.e. at L/2 from the point A).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

L+I 7 (ab)" a-bm f 2 1 TY –314 - 2- 6 STATICS ENGINEERS MECHANICS CHAPTER Lecture Notes: = m %3D EXAMPLE: 22 einber 6O 3.45 m 1.25 m + 3 Pz 1.85 m 1 1.22 m Wa120 IN A weight W• 120 kM is being supported by steel sections with force T. force and force C. The coordinates of A. B. C. and D are given. Assume that E is the origin (0.0.0). Determine Forces T. F, and C.
SHOW COMPLETE SOLUTION
Answer would be appreciated
Answer the problem question, use 2 decimal places as final answer ( Examples of 2 decimal: 62.067 write as 62.07 ) Then box the final answer. Don’t forget the unit. Write it on paper, showing the correct answer and solution.
The plate shown in the figure is fastened to the fix member by three 10 mm diameter rivets. Compute the value of the loads P so that the shearing stress of any rivet does not exceed 70 Mpa.
please help! upvote will be given. NO LONG EXPLANATION NEEDED STRENGTH OF MATERIALS The compound shaft carries the two torques shown. The shear moduli are 28 GPa for aluminum, 83 GPa for steel, and 35 Gpa for bronze. If T = 1179.9 Nm, U = 4330 Nm, x = 3.03 m, y = 2.25 m, z = 1.34 m, d = 94 mm, and e = 76 mm, find the angle of rotation of the free end of the shaft. Round off the final answer to two decimal places.
Read the question carefully and give me right solution according to the question
1. Please show your complete solution. Please typewritten for upvote.
Urgent please solve quickly. a = 10 , b = 7 solve this question about this information. Extra information: Take both loads 35 kN
Please provide a detailed solution. ( The slightly less visible value in below diagram is 8” )
For the solution for this problem, I was wondering how they got 0.75s and the 0.25 in the graph? I thought in the muller method you replace the point of interest with 1 unit load up? Can you please show all calculations so I can see where the 0.75s and 0.25 are coming from
The question is in the picture. Thanks