A timber pile of length 8m and diameter of 0.2m is driven with a 20 kN drop hammer, falling freely from a height of 1.5 m. The total penetration of the pile in the last 5 blows is 40mm. Use the Engineering News Record expression. Assume a factor of safety of 6 and empirical factor (allowing reducing in the theoretical set, due to energy losses) of 2.5 cm. The safe Load carrying capacity of the pile (in kN, round off to 2 decimal places) is

A timber pile of length 8m and diameter of 0.2m is driven with a 20 kN drop hammer, falling freely from a height of 1.5 m. The total penetration of the pile in the last 5 blows is 40mm. Use the Engineering News Record expression. Assume a factor of safety of 6 and empirical factor (allowing reducing in the theoretical set, due to energy losses) of 2.5 cm. The safe Load carrying capacity of the pile (in kN, round off to 2 decimal places) is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The wooden pile shown in the figure has a diameter of 100 mm and is subjected to a load of P = 70 kN. Along the length of the pile and around its perimeter, soil supplies a constant frictional resistance of w = 4.99 kN/m. The length of the pile is L = 4.2 m and its elastic modulus is E = 8.7 GPa.Calculate(a) the force FB needed at the base of the pile for equilibrium.(b) the magnitude of the downward displacement at A relative to B.
Please round to the nearest Hundredth (i.e., 0.01). No Comma! A square pile is driven into a homogeneous sand layer. The pile's width (diameter) is 0.5m. The standard penetration resistance near the vicinity of the pile is 21. Calculate the ultimate point force (Qp) of the pile. Use Briaud & Tucker method. Hint: Qp = qp x Ap Qp = kN
7. If a 45 cm diameter pipe pile is driven into clayey soil to a depth of 12 m. (a) what would the allowable load capacity (Q) be? The water table is 2 m below the ground surface and the soil profile consists of two clay layers (refer to the figure below). Use the ß method to calculate skin friction and the R=30° for all clay layers. (b) Explain how you selected FS value you use. 12 m ▶ 9m 2m 45 cm Y = 18.5kN/m³ = 30kN/m² Ysat = 19kN/m³ C₂ = 30kN/m² Ysat = 20kN/m² S = 60kN/m²
A concrete pile is 15 m long and has 406 mm diameter circular cross section. The pile is fully embedded in sand, for which the unit weight '( = 18 kN/m3 and the frictional angle 8 = 30°. i) Calculate the ultimate point load Qp ii) Determine the total frictional resistance Qs iii) Determine the total ultimate load ofthe pile.
The wooden pile shown in the figure has a diameter of 95 mm and is subjected to a load of P = 80 kN. Along the length of the pile and around its perimeter, soil supplies a constant frictional resistance of w = 2.90 kN/m. The length of the pile is L = 5.6 m and its elastic modulus is E = 8.6 GPa.Calculate(a) the force FB needed at the base of the pile for equilibrium.(b) the magnitude of the downward displacement at A relative to B.
The wooden pile shown in the figure has a diameter of 105 mm and is subjected to a load of P = 70 kN. Along the length of the pile and around its perimeter, soil supplies a constant frictional resistance of w = 3.85 kN/m. The length of the pile is L = 4.0 m and its elastic modulus is E= 12.9 GPa. Calculate (a) the force Fg needed at the base of the pile for equilibrium. (b) the magnitude of the downward displacement at A relative to B. y L Answers: (a) FB = (b) UA= i i B FB KN mm
Please round to the nearest Hundredth (i.e., 0.01). No Comma! A square pile, 13 m long is driven into a homogeneous sand layer. The pile's width (diameter) is 0.5 m. The standard penetration resistance near the vicinity of the pile is 17. Calculate the allowable bearing force (Qa) of the pile. Use FS = 2 and Briaud & Tucker method. Hint: Qa = Qu / FS Qa = KN
ge 4 Please round to the nearest Hundredth (i.e., 0.01). No Comma! A square pile, 26 m long is driven into a homogeneous sand layer. The pile's width (diameter) is 0.2 m. The standard penetration resistance near the vicinity of the pile is 17. Calculate the allowable bearing force (Qa) of the pile. Use FS = 3 and Briaud & Tucker method. Hint: Qa= Qu/FS Qa = kN S D F G H J Finish attempt... K
Using Engineering News formula, the allowable Load (Q) of a wooden pile hammered with a drop hammer (W = 30 kN), having free fall (H) 1.5 m, penetration in last blow (S) 5 mm, using empirical constant (C) as 2,5 and factor of safety as 6, will be
SITUATION 13: A 0.30 m square prestressed concrete pile that is 10 m long is to be driven in a clayey soil whose unconfined compressive strength is 115 kN/m³. The unit weight of clayey is 18 kN/m³. The pile has a design capacity of 360 kN.45. Which of the following most nearly gives the end bearing capacity of pile if Nc=9?a. 25.63 Kn b. 41.55 KN c. 46.58 Kn d. 18.65 Kn46. Which of the following gives the skin friction capacity of pile if =0.76? a. 583.29 Kn b. 680.47 Knc. 501.65 Kn d. 605.21 Kn47. Which of the following most nearly gives the pile capacity if factor of safety is 2.0? a. 420.5 Kn b. 260.5 KN c. 186.6 Kn d. 363.5 Kn
Question- A square pile group of 9 piles having depth of 9 m passes through a recently filled up material of 4.5 m depth. The diameter of the pile is 30 cm and pile spacing is 60 cm centre to centre. If the unconfined compressive strength of the cohesive material is 60 kN/m² and unit weight is 15 kN/m³, the negative skin friction of the pile group is un kN.
Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement is set not exceed 3% of the pile diameter and the overconsolidated ratio (OCR) of the clay is more than 1. The groundwater table is located 15m beneath the ground level. The diameter of the pile, b is 0.5m and the spacing between piles, s is 2m.The pile group is subjected to foundation load of 5425kN. The laboratory testing data for the soil samples taken are as follows: At 5m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 150kN/m? At 10m, eo = 0.55, Cc = 0.32, Cs = 0.09, o'o = 225kN/m2 %3D At 12m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 300KN/m2 %3D 7m 5m Clay 3 10m Unit weight = 18KN/m %3D Friction angle = 0 degree 2 Cohesion = 100KN/m