A timber beam AB of a span of 5 m, a width of 150 mm, and a height of 250 mm is to support three concentrated loads shown in the figure. Calculate the maximum shear and normal stresses for the selected timber beam for the given loading conditions. The selected grade of timber has the following material allowable; T₁=1 MPa and ₁=10 MPa. 15 KN 0.5 m 10 kN 1.0 m 5.0 m 15 KN 1.0 m 0.5 m B 150 mm 250 mm Cross Section

A timber beam AB of a span of 5 m, a width of 150 mm, and a height of 250 mm is to support three concentrated loads shown in the figure. Calculate the maximum shear and normal stresses for the selected timber beam for the given loading conditions. The selected grade of timber has the following material allowable; T₁=1 MPa and ₁=10 MPa. 15 KN 0.5 m 10 kN 1.0 m 5.0 m 15 KN 1.0 m 0.5 m B 150 mm 250 mm Cross Section

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cantilever timber beam with a span of L= 2.6 m supports a uniformly distributed load w. The beam width is b = 270 mm and the beam height is h = 230 mm. The allowable bending stress of the wood is 7.2 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w = i kN/m.
A cantilever timber beam with a span of L = 2.2 m supports a uniformly distributed load w. The beam width is b = 340 mm and the beam height is h = 210 mm. The allowable bending stress of the wood is 6.7 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w = i kN/m. W L B b h
Problem 3: A rectangular column with a width of 3 in. and a depth of 6 in. is pinned at both ends and has a length of 20 ft. The column is made of wood with Young's modulus of 10,000 ksi. The column carries an axial compressive force P. a. Determine the critical load to buckle the column. b. If the yield stress is 6 ksi, is the column more likely to buckle or fail by yielding?
A simply supported wood beam with a span of L = 6 m supports a uniformly distributed load of w= 13 kN/m. The allowable bending stress of the wood is 10 MN/m². If the aspect ratio of the solid rectangular wood beam is specified as h/b = 1.5 as shown in Fig. (3). (a) determine the minimum width b and corresponding beam height h that can be used for the beam. (b) If the beam width is 15 cm and the beam height is 25 cm and the allowable bending stress of the wood is 6 MN/m2 at the same span. Determine the magnitude of the maximum load w that may be carried by the beam. w kN/m 6 m B 0000 16- h
A cantilever timber beam with a span of L = 2.8 m supports a uniformly distributed load w. The beam width is b = 320 mm and the beam height is h = 250 mm. The allowable bending stress of the wood is 6.4 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w = i kN/m. W L B b h
Correct answer only.
5/Determine the smallest value of uniform load that will cause a crack for the reinforced concrete beam shown below. Use f= 30 MPa Wer=? 3.6 m- Ø16mm 100 600 100-> 100 200 50
The floor of a classroom is made of 150mm thick lightweight concrete. If the floor slab having a length of 8m and width of 6m determine the resultant force in Kn caused by a. dead load b. live load c. total load lightweight concrete is 0.015KN/m^2 per mm thickness and classroom is 1.92KN/m^2
A wooden joist 15 cm deep by 7.5 cm wide is reinforced by gluing to its lower face a steel strip 7.5 cm wide by 0.3 cm thick. The joist is simply-supported over a span of 3 m and carries a uniformly distributed load of 5000 N. Find the maximum direct stresses in the wood and steel and the maximum shearing stress in the glue. Take Es/Et = 20. (Cambridge) Answer: wood 4.56 MN/m2; steel 52.9 MN/m2; glue 0.21 MN/m2. Show your solution
(NOS 2 – 13) PROBLEM 1. A timber beam shown in the figure is made up of Sasalit (50% stress grade), Use LRFD. All the given loads shown in the figure below are unfactored service loadings only, it does not include the weight of the beam itself. 8.) What is the maximum actual moment in KN-m? 9) What is the actual maximum bending stress in MPa? 10) What is the actual maximum shearing stress in MPa? 11) What is the moment of inertia of the beam in mm4 with respect to x-axis? 12) What is the moment of inertia of the beam in mm4 with respect to y-axis? 13) The allowable deflection for beams is L/240, what is the allowable deflection in mm.? PDL = 5 KN %3D 500 mm PLL = 3 KN Wp =6 KN/m WL 3 KN/m 800 mm R1 R2 2 m 1 m 1 m
A cantilever timber beam with a span of L = 3.7 m supports a uniformly distributed load w. The beam width is b = 320 mm and the beam height is h = 270 mm. The allowable bending stress of the wood is 5.7 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w = i kN/m. Save for Later Attempts: 0 of 1 used Submit Answer
• Figure below shows a house floor which uses 50 mm wide x 150 mm deep timber joists spaced at 400 mm centres. If the maximum permissible stress in the timber is limited to 7.5 N/mm2, determine the maximum allowable simply supported span of the floor if it supports the following loads: • Dead Load of floor • Imposed Load of floor = 1.5kN/m² = 0.45kN/m? Floor boards Span Ceiling 150 Joist 50 400 mm 6/23/2021 28