A cantilever timber beam with a span of L = 2.3 m supports a uniformly distributed load w. The beam width is b = 330 mm and the beam height is h = 160 mm. The allowable bending stress of the wood is 7.3 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w = i kN/m.

A cantilever timber beam with a span of L = 2.3 m supports a uniformly distributed load w. The beam width is b = 330 mm and the beam height is h = 160 mm. The allowable bending stress of the wood is 7.3 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w = i kN/m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

E5
A timber column, 8 in. × 8 in. in cross section, is reinforced on each side by a steel plate 8 in. wide and t in. thick. Determine the thickness t so that the column will support an axial load of 300 kips without exceeding a maximum timber stress of 1200 psi or a maximum steel stress of 20 ksi. The moduli of elasticity are 1.5 × 106 psi for timber, and 29 × 106 psi for steel.
A cantilever timber beam with a span of L = 2.8 m supports a uniformly distributed load w. The beam width is b = 260 mm and the beam height is h = 210 mm. The allowable bending stress of the wood is 5.2 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w = i kN/m.
A cantilever timber beam with a span of L = 2.6 m supports a uniformly distributed load w. The beam width is b = 250 mm and the beam height is h= 140 mm. The allowable bending stress of the wood is 5.9 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w= i eTextbook and Media Save for Later kN/m. Attempts: 0 of 3 used Submit Answer
solve for the wind load on the right side
solve the wind load on the left side
Answer problem1
4. Steel and aluminum plates are used to reinforced 100 x 175 mm timber beam. The three materials are fastened firmly as shown so that there will be no relative movement between them. Given the following material properties, determine the safe resisting moment of the beam in KN.M. Allowable bending stress, Fb Modulus of Elasticity, E Steel = 130MPA Steel = 210MPA Aluminum = 90 MPa Aluminum = 80 MPa Wood = 20 MPa Wood = 15 MPa 30 mm CTEEL WOOD ww.skl A LUMINUM 140 mm
The steel framework shown below is used to support the reinforced concrete slab (unit weight of concrete =23.6KN/m3) that is used for an office use (minimum live load = 2.4KPa). The slab is 150 mm thick. Use a=3m, b=5m. Neglect the self-weight of the beam and girder. Assume all beams and girders have simple supports. NSCP 2015 Load factors: 1.2DL & 1.6LL. Calculate the total ultimate/factored liveload in Kilo Pascals? Express your answer in 2 decimal places
A simply supported wood beam with a span of L = 22 ft supports a uniformly distributed load of w0 = 280 lb/ft. The allowable bending stress of the wood is 1.30 ksi. If the aspect ratio of the solid rectangular wood beam is specified as h/b = 3.00, calculate the minimum width b that can be used for the beam.
A simply supported wood beam of length L = 8 ft carries a concentrated load P at midspan, as shown. The cross- sectional dimensions of the beam are b = 7 in. and h = 13 in. If the allowable shear strength of the wood is 130 psi, determine the maximum load P that may be applied at midspan. Neglect the effects of the beam's self-weight. 12 Answer: P = IM P B 7/2 C X lb N b h